MAX16963 Dual 2.2MHz, Low-Voltage Step-Down DC-DC Converter General Description Benefits and Features The MAX16963 is a high-efficiency, dual synchronous S Small Size Components step-down converter that operates with a 2.7V to 5.5V Dual 2.2MHz DC-DC Converter input voltage range and provides a 0.8V to 3.6V output S Ideal for Point-of-Load Applications voltage range. The device delivers up to 1.5A of load Up to 1.5A Output Current current per output. The low input/output voltage range Adjustable Output Voltage: 0.8V to 3.6V and the ability to provide high output currents make this 2.7V to 5.5V Operating Supply voltage device ideal for on-board point-of-load and postregulation S High Efficiency at Light Load applications. The device achieves Q3% output error over Skip Mode with 36A Quiescent Current load, line, and temperature ranges. S Low Electromagnetic Emission The device features a 2.2MHz fixed-frequency PWM mode Programmable SYNC I/O Pin for better noise immunity and load transient response, Spread Spectrum and a skip mode for increased efficiency during light-load operation. The 2.2MHz frequency operation allows for S Low Power Mode Saves Energy Independent Enable Inputs an all-ceramic capacitor design and small-size external components. An optional spread-spectrum frequency S Output Rail Monitoring Helps Prevent System Failure modulation minimizes radiated electromagnetic emissions Open-Drain Power-Good Output due to the switching frequency. S Limits Inrush Current During Startup On-board low R switches help minimize efficiency DSON Built-In Soft-Start Timer losses at heavy loads and reduce critical/parasitic induc- S Overtemperature and Short-Circuit Protections tance, making the layout a much simpler task with respect S 4mm x 4mm, 16-Pin TQFN and 16-Pin TSSOP to discrete solutions. Following a simple layout and footprint Packages ensures first-pass success in new designs. S -40NC to 125NC Operating Temperature Range The device is offered in a factory-preset output voltage or adjustable output-voltage version (see the Selector Guide for options). Factory-preset output-voltage versions allow Typical Application Circuit customers to achieve Q3% output-voltage accuracy without using external resistors, while the adjustable output-voltage version provides the flexibility to set the output voltage to V PV1 any desired value between 0.8V and 3.6V using an external PV1 OUTS1 resistive divider. 2.2H 4.7F EN1 LX1 V OUT1 Additional features include 8ms fixed soft-start, 16ms V PV2 22F fixed power-good delay, overcurrent, and overtemperature PV2 PGND1 protections. 4.7F EN2 The MAX16963 is available in thermally enhanced 16-pin OUTS2 1.5H V PV TSSOP-EP and 4mm x 4mm, 16-pin TQFN-EP packages, V LX2 OUT2 10 and is specified for operation over the -40NC to +125NC PV 22F automotive temperature range. PGND2 1F GND V V OUT1 OUT2 Applications Automotive Postregulation 20k MAX16963 20k Industrial/Military PG2 PG1 EP Point-of-Load Applications Ordering Information appears at end of data sheet. For related parts and recommended products to use with this part, refer to: www.maximintegrated.com/MAX16963.related For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxims website at www.maximintegrated.com. 19-6487 Rev 1 9/13MAX16963 Dual 2.2MHz, Low-Voltage Step-Down DC-DC Converter ABSOLUTE MAXIMUM RATINGS PV, PV1, PV2 to GND ..............................................-0.3V to +6V TQFN (derate 25mW/NC above +70NC)................... 2000mW* EN1, EN2, PG1, PG2 to GND .................................-0.3V to +6V TSSOP (derate 26.1mW/NC above +70NC)........... 2088.8mW* LX Current ........................................................... 1.6 (Note 1) Operating Temperature Range ........................ -40NC to +125NC PGND1 and PGND2 to GND ..............................-0.3V to +0.3V Junction Temperature .....................................................+150NC PV to PV1 and PV2 ...............................................-0.3V to +0.3V Storage Temperature Range ............................ -65NC to +150NC LX1 and LX2 Continuous RMS Current ...................................1A Lead Temperature (soldering, 10s) ................................+300NC All Other Pins Voltages to GND .. (V + 0.3V) to (V - 0.3V) Soldering Temperature (reflow) ......................................+260NC PV GND Output Short-Circuit Duration ....................................Continuous Continuous Power Dissipation (T = +70NC) A *As per JEDEC51 Standard (multilayer board). Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional opera- tion of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note 1: LX has internal clamp diodes for PGND and PV . Applications that forward bias these diodes should take care not to exceed the ICs package power-dissipation limits. PACKAGE THERMAL CHARACTERISTICS (Note 2) TQFN TSSOP Junction-to-Ambient Thermal Resistance (B ) ..........40NC/W Junction-to-Ambient Thermal Resistance (B ) .......38.3NC/W JA JA Junction-to-Case Thermal Resistance (B ) .................6NC/W Junction-to-Case Thermal Resistance (B ) .................3NC/W JC JC Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. ELECTRICAL CHARACTERISTICS (V = V = V = 5V, V = 5V, T = T = -40C to +125C, unless otherwise noted. Typical values are at T = +25C.) (Note 3) PV PV1 PV2 EN A J A PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Supply Voltage Range V Normal operation 2.7 5.5 V PV Supply Current I No load, V = 0V 16 36 60 FA PV PWM Shutdown Supply Current I V = V = 0V, T = +25 C 1 5 FA SHDN EN1 EN2 A Undervoltage Lockout Threshold V 2.37 V UVLO L Low Undervoltage Lockout Threshold V 2.6 V UVLO H High Undervoltage Lockout Hysteresis 0.07 V SYNCHRONOUS STEP-DOWN DC-DC CONVERTER 1 I = 4% to 100% -3 0 +3 % LOAD Feedback Set-Point Accuracy V OUTS1 I = 0% -0.5 +2 +3 % LOAD pMOS On-Resistance R V = 5V, I = 0.4A 90 148 mI DSON P1 PV1 LX1 nMOS On-Resistance R V = 5V, I = 0.8A 68 128 mI DSON N1 PV1 LX1 Maximum pMOS Current-Limit I 1.95 2.35 3.15 A LIMP1 Threshold Maxim Integrated 2