Evaluate: MAX2045/MAX2046/MAX2047 19-2793 Rev 0a 4/03 MAX2045/MAX2046/MAX2047 Evaluation Kits General Description Features The MAX2045/MAX2046/MAX2047 evaluation kits Easy Evaluation of the MAX2045/MAX2046/ (EV kits) simplify evaluation of the MAX2045/MAX2046/ MAX2047 MAX2047 vector multipliers. Each kit enables testing of +4.75V to +5.25V Single-Supply Operation the devices RF performance and requires no additional support circuitry. The EV kit input and output use SMA Include RF Input and Output Matching connectors and baluns (for single-ended-to-differential 2040MHz to 2240MHz (MAX2045) conversions) to facilitate the connection to RF test 1740MHz to 2060MHz (MAX2046) equipment. 790MHz to 1005MHz (MAX2047) Each EV kit is assembled with either the MAX2045, Configurable for Current-Control Mode and MAX2046, or MAX2047 and incorporates all matching Single-Ended and Differential Voltage-Control components optimized for the corresponding band of Mode frequency operation. Fully Assembled and Tested Ordering Information Component Suppliers PART TEMP RANGE IC PACKAGE SUPPLIER PHONE FAX Murata 800-831-9172 814-238-0490 MAX2045EVKIT -40C to +85C 32 QFN-EP* MAX2046EVKIT -40C to +85C 32 QFN-EP* Toko 800-745-8656 MAX2047EVKIT -40C to +85C 32 QFN-EP* Note: When contacting these suppliers, please indicate that you are using the MAX2045/MAX2046/MAX2047. *EP = Exposed paddle. MAX2045 Component List DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION 1.5pF 0.1pF, 50V C0G ceramic 22pF 5%, 50V C0G ceramic L1 1 capacitor (0402) C1, C4C16 14 capacitors (0402) Murata GRP1555C1H1R5B Murata GRP1555C1H220J 8.2nH 5% chip inductor (0402) 220pF 10%, 50V X7R ceramic L2 1 Toko LL1005-FH8N2J capacitors (0402) C2, C3 2 Murata GRP155R71H221K 280 1% resistor (0402) R1 1 Any 0.01F 10%, 25V X7R ceramic R2, R4, R6 0 Not installed C17 1 capacitor (0402) Murata GRP155R71E103K 0 resistors (0402) R3, R5 2 Any PC board edge-mount SMA RF J1, J2 2 connectors (flat-tab launch) 1:1 balun (50:50) T1 1 EFJohnson 142-0741-856 Murata LDB15C500A1900 4:1 balun (200:50) Header, 10 x 2, 0.100in spacing T2 1 J3 1 Murata LDB15C201A1900 Molex 10-89-1201 U1 1 MAX2045ETJ-T (32-pin QFN) Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct at 1-888-629-4642, or visit Maxims website at www.maxim-ic.com.MAX2045/MAX2046/MAX2047 Evaluation Kits MAX2046 Component List MAX2047 Component List DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION 3.9pF 0.1pF, 50V C0G ceramic 47pF 5%, 50V C0G ceramic C1 1 capacitor (0402) C1C16 16 capacitors (0402) Murata GRP1555C1H3R9B Murata GRP1555C1H470J 220pF 10%, 50V X7R ceramic 0.01F 10%, 25V X7R ceramic C17 1 capacitor (0402) C2, C3 2 capacitors (0402) Murata GRP155R71H221K Murata GRP155R71E103K 22pF 5%, 50V C0G ceramic PC board edge-mount SMA RF C4C13, J1, J2 2 connectors (flat-tab launch) 12 capacitors (0402) C15, C16 Murata GRP1555C1H220J EFJohnson 142-0741-856 Header 10 x 2, 0.100in spacing 6.2pF 0.25pF, 50V C0G ceramic J3 1 Molex 10-89-1201 C14 1 capacitor (0402) Murata GRP1555C1H6R2C 15nH 5% chip inductor (0402) L1 1 Toko LL1005-FH15NJ 0.01F 10%, 25V X7R ceramic capacitor (0402) C17 1 39nH 5% chip inductor (0402) L2 1 Murata GRP155R71E103K Toko LL1005-FH39NJ 280 1% resistor (0402) PC board edge-mount SMA RF R1 1 Any J1, J2 2 connectors (flat-tab launch) EFJohnson 142-0741-856 R2, R4, R6 0 Not installed Header 10 x 2, 0.100in spacing 0 resistors (0402) J3 1 R3, R5 2 Any Molex 10-89-1201 1:1 balun (50:50) 1.5pF 0.1pF, 50V C0G ceramic T1 1 Murata LDB20C500A900 L1 1 capacitor (0402) Murata GRP1555C1H1R5B 4:1 balun (200:50) T2 1 Murata LDB20C201A900 12nH 5% chip inductor (0402) L2 1 Toko LL1005-FH12NJ U1 1 MAX2047ETJ-T (32-pin QFN) 280 1% resistor (0402) R1 1 Quick Start Any The MAX2045/MAX2046/MAX2047 EV kits are fully R2, R4, R6 0 Not installed assembled and factory tested. Follow the instructions 0 resistors (0402) in the Connections and Setup section for proper R3, R5 2 Any device evaluation. The EV kits come configured for sin- gle-ended, voltage-control operation. For differential 1:1 balun (50:50) T1 1 voltage- or current-mode operation, see the Detailed Murata LDB15C500A1900 Description section. 4:1 balun (200:50) T2 1 Murata LDB15C201A1900 Test Equipment Required Table 1 lists the required test equipment to verify the U1 1 MAX2046ETJ-T (32-pin QFN) MAX2045/MAX2046/MAX2047 operation. It is intended as a guide only, and some substitutions are possible. Connections and Setup This section provides a step-by-step guide to operat- ing the EV kits and testing the devices functions. Do not turn on DC power or RF signal generators until all connections are made. 2 Evaluate: MAX2045/MAX2046/MAX2047