Click here for production status of speci c part numbers. Evaluates: MAX30001 MAX30001 Evaluation System MAX30002 General Description Features The MAX30001 evaluation system (EV system) provides Convenient Platform to Evaluate the MAX30001 a single platform to evaluate the functionality and features Many Easy-to-Reach Test Points of the MAX30001 with Biopotential (ECG, R-to-R, and Measure Individual Supply Currents Pace Detection) and Bioimpedance (BioZ) measurement capabilities. The EV system includes a MAX30001 evaluation Touchproof Cable Connectors kit (EV kit) and a MAX32630FTHR Cortex-M4F Windows 7/8/10 Compatible GUI software microcontroller for wearables. The MAX32630FTHR Fully Assembled and Tested provides power to the MAX30001 EV kit and contains the Facilitates IEC 60601-2-47 Compliance Testing rmware necessary to use the EV kit GUI program. The EV kit ships with jumpers installed and supply voltages set Ultra-Low-Power Design to typical operating values. Optional connections exist which can be shunted to make use of di erent functionalities. EV System Contents Note that the MAX30002 is register compatible with the MAX30001 EV kit MAX30001. By disabling the ECG, PACE, and R-to-R MAX32630FTHR blocks, the MAX30001 is equivalent to the MAX30002 USB A to micro-USB cable and the EV kit evaluates the MAX30002 functionality and Three (3) ECG cables performance. This EV system is not a medical device. Ordering Information appears at end of data sheet. MAX30001 EV Kit Photo Windows is a registered trademark and registered service mark of Microsoft Corporation. 319-100083 Rev 1 5/18Evaluates: MAX30001 MAX30001 Evaluation System MAX30002 MAX30001 Evaluation System Files FILE DECRIPTION MAX30001EVKit.exe PC GUI Program sure you want to run this software appears, select Quick Start the Yes option. Required Equipment 7) When the installer GUI appears, click Next. Select Note: In the following sections, software-related items are the installation paths and if a shortcut should be identi ed by bold text. Text in bold refers to items directly created on the desktop. When prompted, press from the install of EV kit software. Text which is bold and Install. Once complete, click Close. underlined refers to items from the Windows operating 8) Double-click the shortcut to start the GUI. Alternatively, go system. to Start All Programs. Look for the MAX30001EVKitSoftware folder and click on the MAX30001 EV kit MAX30001EVKitSoftware.EXE le inside the folder. MAX32630FTHR 9) After the initial splash screen, when the GUI Micro-USB cable appears, the text in the right eld of the status strip at the bottom of the GUI window should display Windows PC with USB port Hardware Connected and the COM port associated Procedure with the EV kit. The EV kit is fully assembled and tested. Follow the steps Detailed Description of Software below to verify board operation: Software Startup 1) Con rm that the MAX32630FTHR is rmly seated in connectors J8 and J7 in the proper orientation. If the EV system is connected when the software is 2) Set the EV kit hardware on a nonconductive surface opened, the software rst initializes the hardware to com- to ensure that nothing on the PCB shorts together. municate. The software then reads the device registers 3) Connect the EV kit hardware to a PC with the and updates all the associated control elds displayed on provided USB cable. Attach the micro-USB end the GUI. The status strip at the bottom of the GUI displays to the MAX32630FTHR board and the type A end MAX32630FTHR rmware version, the GUI version, and to the host PC. Once connected, LED D1 on the the hardwares associated COM port. MAX32630FTHR will blink red and LED D1 on the If the EV system is not connected on startup, the EV kit board will be green. Connection Issue dialog box shown in Figure 1 appears 4) Windows should automatically begin installing the after the GUI splash screen. Clicking OK opens the necessary device driver. The USB interface of the Connection window of the GUI. Use the Scan Ports but- EV kit hardware is con gured as an HID device and ton to identify all COM ports in use by the PC and select therefore does not require a unique/custom device the port associated with the EV kit hardware in the COM driver. Once the driver installation is complete, a Port drop down menu. This window, shown in Figure 2, Windows message appears near the System Icon may appear if connecting to the EV kit for the rst time menu, indicating that the hardware is ready to use. even if the hardware is connected before starting the GUI. Do not attempt to run the GUI prior to this message. Once the correct COM port is selected, press Connect at If you do, then you must close the application and the bottom center of the GUI to enter the main window. restart it once the driver installation is complete. On The program reads all device registers and updates the some versions of Windows, administrator privileges control elds of the GUI. may be required to install the USB device. 5) Once the device drivers have been installed, down- ToolStrip Menu Bar load the latest EV kit software (MAX30001EVKitSoft- The ToolStrip menu bar (Figure 3) is located at the top wareInstall.ZIP) and extract it to a temporary folder. of the GUI window. This bar comprises the File, Device, 6) Open the extracted ZIP folder and double-click the Options, Logging, and Help menus whose functions are .EXE le to run the installer. If a message box stating detailed in the following sections. The publisher could not be veri ed. Are you Maxim Integrated 2 www.maximintegrated.com