Click here for production status of specific part numbers. MAX40002MAX40005 nanoPower 4-Bump Comparator in Ultra-Tiny MAX40012MAX40015 0.73mm x 0.73mm WLP/SOT23 Packages General Description Benefits and Features The MAX40002MAX40005 and MAX40012MAX40015 Tiny 0.73mm x 0.73mm, 4-Bump WLP and 5-Pin tiny, single comparators are ideal for a wide variety of SOT23 Packages Save Board Space portable electronics applications such as cell phones, Ultra-Low 500nA Operating Current Preserves media players, and notebooks that have extremely tight Battery Power in Applications Where Comparator is board space and power constraints. These comparators Constantly Monitoring are offered in both, a miniature 4-bump wafer-level pack- 1.7V to 5.5V Supply Range Allows Operation from age (WLP) with a 0.73mm x 0.73mm footprint (as small as 1.8V, 2.5V, 3V and 5V Systems two 0402 resistors) and a 5-pin SOT23 package. Input Voltage Range: 0.1V to 5.5V This device family operates with a supply voltage range from 1.7V to 5.5V (either V or external V ), and External REF Range: 1.7V to 5.5V CC REF consumes only 500nA of supply current. These devices Wide Variety of Factory-Trimmed Reference Voltages have a wide input-voltage range of 0.1V to 5.5V, independent Saves Space and Cost of External Reference: of the supply voltage, and maintain high impedance at 0.2V, 0.5V, 0.9V, 1.222V the inputs even when powered down (V or external CC 9s Propagation Delay V = 0V). They also feature internal filtering to provide REF -40C to +125C Specified Temperature Range high RF immunity. The MAX40002MAX40003 and MAX40012MAX40013 have open-drain outputs, while the MAX40004MAX40005 Ordering Information appears at end of data sheet. and MAX40014MAX40015 feature push-pull outputs. The MAX40002/MAX40004 and MAX40012MAX40014 have noninverting inputs, while the MAX40003/MAX40005 and MAX40013MAX40015 have inverting inputs (see the Selector Guide for more information). These devices also come with an internal reference. The reference voltage is preset at the factory and parts are offered with the following voltage options: 0.2V, 0.5V, 0.9V or 1.222V (see Ordering Information table). These devices are fully specified over -40C to +125C automotive temperature range. Applications Mobile Devices Portable Medical Devices Portable Instrumentation Notebook Computers Electronic Toys 19-8574 Rev 8 5/20MAX40002MAX40005 nanoPower 4-Bump Comparator in Ultra-Tiny MAX40012MAX40015 0.73mm x 0.73mm WLP/SOT23 Packages Absolute Maximum Ratings V /REF to GND ..................................................-0.3V to +6V Operating Temperature Range ......................... -40C to +125C CC IN to GND ...............................................................-0.3V to +6V Junction Temperature ......................................................+150C OUT (Open-Drain) to GND .....................................-0.3V to +6V Storage Temperature Range ............................ -65C to +150C OUT (Pushpull) to GND .............................-0.3V to V + 0.3V Lead Temperature (soldering, 10s) .................................+300C CC Continuous Current Into Any Input/Output .......................20mA Soldering Temperature (reflow) .........................................260C Continuous Power Dissipation (T = +70C) A 4-Bump WLP (Derate 9.58mW/C above +70C) ....766.4mW 5-Pin SOT (Derate 3.9mW/C above +70C ............312.6mW Package Thermal Characteristics (Note 1) WLP SOT23 Junction-to-Ambient Thermal Resistance ( ) ...104.41C/W Junction-to-Ambient Thermal Resistance ( ) .....255.9C/W JA JA Junction-to-Ambient Thermal Resistance ( ) ..........81C/W JC Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics V /REF = 3.3V, R = 100k to V = 3.3V, R = , C = 20pF, T = T to T . Typical values are at T = +25C, CC PULLUP PULLUP L L A MIN MAX A unless otherwise noted. (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS POWER SUPPLY VOLTAGE V /REF Supply Voltage CC V /V 1.7 5.5 V CC REF Range V > 0, V = low, IN OUT no output or reference load current, 0.5 1.1 T = -40C to +85C A V /REF Supply Current I A CC CC V > 0, V = low, IN OUT no output or reference load current, 1.3 T = -40C to +125C A Power-Up Time 0.5 ms COMPARATOR V CC T = +25C 0.1 A + 0.1 Input Voltage Range V V IN T = -40C to +125C 0.1 V A CC Over V range, IN 0.5 27 Input Offset Voltage T = -40C to +85C A (For External V only) V mV REF OS Over V range, (Note 3) IN 32 T = -40C to +125C A Maxim Integrated 2 www.maximintegrated.com