MAX4426/ MAX4427/MAX4428 Dual High-Speed 1.5A MOSFET Drivers General Description Features The MAX4426/MAX4427/MAX4428 are dual monolithic S Upgrade for TSC4426/TSC4427/TSC4428 MOSFET drivers designed to translate TTL/CMOS inputs S Lower On Resistance: 4 vs. 7 to high voltage/current outputs. The MAX4426 is a dual S Shorter Delay Times: t - 10ns vs. 30ns D1 inverting power MOSFET driver. The MAX4427 is a dual t - 25ns vs. 50ns D2 noninverting power MOSFET driver, and the MAX4428 contains one inverting section and one noninverting S 1.5A Peak Output Current section. Delay times are nearly independent of V DD S Fast Rise and Fall Times: Typically 20ns with (see Typical Operating Characteristics). High-current 1000pF Load output drivers rapidly charge and discharge the gate S Wide Operating Range: 4.5V to 18V capacitance of even the largest power MOSFETs to S Low Power Consumption: 1.8mA with Logic 1 Input within millivolts of the supply rails. This produces the 200A with Logic 0 Input power MOSFETs minimum on resistance. The MAX4426/ MAX4427/MAX4428 s high speed minimizes power loss- S TTL/CMOS Compatible es in switching power supplies and DC-DC converters. S Latchup Protected-Withstand > 500mA Reverse Current Applications S ESD Protected Switching Power Supplies DC-DC Converters Ordering Information Motor Controllers PART TEMP RANGE PIN-PACKAGE Pin-Diode Drivers MAX4426CPA 0NC to +70NC 8 Plastic DIP Charge-Pump Voltage Inverters MAX4426CSA 0NC to +70NC 8 SO MAX4426C/D 0NC to +70NC Dice* Pin Configurations MAX4426EPA -40NC to +85NC 8 Plastic DIP TOP VIEW MAX4426ESA -40NC to +85NC 8 SO MAX4426EJA -40NC to +85NC 8 CERDIP N.C. 1 8 N.C. MAX4426MJA -55NC to +125NC 8 CERDIP** INA 2 Functional Diagrams7 OUTA 2, 4 7, 5 MAX4426 Ordering Information continued on end of data sheet. GND 3 6 V DD *Dice are tested at T = +25C. A INB 4 5 OUTB INVERTING **Contact factory for availability and processing to MIL-STD-883. DIP/SO Typical Operating Circuit N.C. 1 8 N.C. V = +18V DD INA 2 7 OUTA 2, 4 7, 5 MAX4427 4.7F 0.1F GND 3 6 V DD INB 4 5 OUTB NONINVERTING DIP/SO MAX4426 2 7 INPUT OUTPUT* N.C. 1 8 N.C. A INA 2 7 OUTA MAX4428 INPUT OUTPUT* GND 3 6 V DD 4 5 Pin Configurations appear at end of data sheet. B INB 4 5 OUTB Functional Diagrams continued at end of data sheet. UCSP is a trademark of Maxim Integrated Products, Inc. DIP/SO For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxims website at www.maxim integrated.com. 19-0132 Rev 2 6/06 AVAILABLEMAX4426/MAX4427/MAX4428 Dual High-Speed 1.5A MOSFET Drivers ABSOLUTE MAXIMUM RATINGS Supply Voltage V to GND .............................................. +20V Operating Temperature Ranges: DD Time V < V < V ......................................................... 50ns MAX442 C ..................................................... 0C to +70C IL IN IH Input Voltage .....................................V + 0.3V to GND - 0.3V MAX442 E .................................................. -40C to +85C DD Continuous Power Dissipation (T = +70C) MAX442 MJA .............................................. -550C to +125C A Plastic DIP (derate 9.09mW/C above +70C) ............727mW Storage Temperature Range ............................ -55C to +160C SO (derate 5.88mW/C above +70C) ........................471mW Maximum Chip Temperature ...........................................+150C CERDIP (derate 8.00mW/C above +70C) ................640mW Lead Temperature (soldering, 10 sec) ...........................+300C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (V = +4.5V to +18V, T = T to T , unless otherwise specified.) DD A MIN MAX PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Logic 1 Input Voltage V 2.4 V IH Logic 0 Input Voltage V 0.8 V IL Input Current I V = 0V to 18V -1 1 A IN IN V - DD Output High Voltage V No load mV OH 25 Output Low Voltage V No load 25 mV OL V = 0.8V for IN T = +25NC 4 10 A inverting stages, V = 2.4V for IN T = T to noninverting A MIN 5 12 V = 18V, T DD stages MAX Output Resistance R I = OUT LOAD V = 2.4V for 10mA IN T = +25NC 4 10 A inverting stages, V = 0.8V for IN noninverting T = T to A MIN 5 12 stages T MAX Peak Output Current I V = 18V 1.5 A PK DD T = +25NC 1.8 4.5 V = +3V for both A IN inputs T = T to T 2.5 8.0 A MIN MAX Power-Supply Current I mA SUPP T = +25NC 0.2 0.4 V = 0V for both A IN inputs T = T to T 0.3 0.6 A MIN MAX T = +25NC 20 30 A Rise Time (Note 1) t ns R T = T to T 25 40 A MIN MAX T = +25NC 20 30 A Fall Time (Note 1) t ns F T = T to T 25 40 A MIN MAX T = +25NC 10 30 A t ns D1 T = T to T 15 40 A MIN MAX Delay Time (Note 1) T = +25NC 25 50 A t ns D2 T = T to T 30 60 A MIN MAX Note 1: Switching times guaranteed by design, not tested. See Figure 1 for timing measurement circuit. 2 Maxim Integrated