Evaluates: MAX5216 MAX5216DACLite Evaluation Kit General Description Features The MAX5216DACLite evaluation kit (EV kit) enables USB Powered, No Addition al Supply Needed* evaluation of the MAX5216 single-channel, low-power, (Cable Not Included) buffered-output, 3-wire SPI interface, 16-bit DAC. The EV 3.3V Fixed VDD from On-Board LDO (MAX8510) M M kit also includes Windows XP -, Windows Vista -, and 3.000V On-Board Precise Voltage Reference M Windows 7-compatible software that provide a simple (MAX6133) graphical user interface (GUI) for exercising the features of the IC. Direct USB Communication through the MAXQ622 Microcontroller The EV kit enables a quick evaluation of the device, with Windows XP-, Windows Vista-, and Windows 7 a fixed supply voltage of 3.3V. The EV kit allows for the generation of selectable waveforms to display DAC AC (32-Bit)-Compatible Software signal-generation capability. SPI Interface Terminals The EV kit can be used as a system hardware debugging Proven PCB Layout tool, or as a signal generator demonstration kit. Fully Assembled and Tested *Since 16 bits is 65,535 levels, the LSB is 45.8V. Depending on how clean the computers USB power is, it may be necessary to provide clean analog power for the best accuracy. Ordering Information appears at end of data sheet. Component List DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION Mini-USB type-B receptacle 1F 10%, 10V X5R ceramic J1 1 C1, C2, Mill-Max 897-43-005-00-100001 6 capacitors (0603) C5C7, C9 TDK C1608X5R1A105K Not installed, 10-pin (5 x 2) J2 0 header, 0.1in 0.01F 10%, 50V X7R ceramic C3 1 capacitor (0603) J3 0 Not installed, 1-pin header, 0.1in TDK CGA3E2X7R1H103K J4 0 Not installed, 1-pin header 0.1F 10%, 16V X7R ceramic Turret terminal pins C4, C8, 4 capacitors (0603) J5, J7, J8 4 Mill-Max C12C14 Murata GRM188R71C104KA01J 2108-2-00-44-00-00-07-0 18pF 5%, 50V C0G ceramic J6 0 Not installed, 4-pin header C10, C11 2 capacitors (0603) Not installed, RF-coax SMA TDK C1608C0GH1180JT J9 0 connector Ferrite bead (0805) Molex 733910060 FB1 1 TDK MMZ20112Y601BT Windows XP, Windows Vista, and Windows are registered trademarks and registered service marks of Microsoft Corporation. 19-6527 Rev 0 11/12Evaluates: MAX5216 MAX5216DACLite Evaluation Kit Component List (continued) DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION 27 1% resistors (0603) 3.000V, 3ppm/C, low-power R1, R2, R10 3 YAGEO RC0603FR-0727RL U3 1 voltage reference (8 MAX) Maxim MAX6133A30+ 1k 1% resistor (0603) R3 1 Panasonic ERJ-3EKF1001V 3.3V ultra-low noise LDO U4 1 (5 SC70) 0 1% resistors (0603) R4R9 6 Maxim MAX8510EXK33+ YAGEO RC0603FR-070RL 16-bit V OUT DAC (8 MAX ) 12MHz crystal oscillator U1 1 Maxim MAX5216GUA+ (HC49US) Y1 1 Abracon Crystals 16-bit microcontroller with ABLS-12.000MH-B4-T U2 1 USB 2.0 interface (64 LQFP) Maxim MAXQ622G-0000+ 1 PCB: MAX5216DACLITE Rev. A Component Suppliers SUPPLIER PHONE WEBSITE Abracon Corporation 945-546-8000 www.abracon.com Mill-Max Mfg. Corp. 516-922-6000 www.mill-max.com Molex 800-768-6539 www.molex.com Murata Electronics North America, Inc. 770-436-1300 www.murata-northamerica.com Panasonic Corp. 800-344-2112 www.panasonic.com TDK Corp. 847-803-6100 www.component.tdk.com YAGEO Corporation www.yageo.com Note: Indicate that you are using the MAX5216 when contacting these component suppliers. Procedure Quick Start The EV kit is fully assembled and tested. Follow the steps Required Equipment below to verify board operation: MAX5216DACLite EV kit 1) Visit www.maximintegrated.com/evkitsoftware to The EV kit board is a plug-n-play device that con- download the latest version of the EV kit software, nects to the PC through a USB-A to Mini-B cable. The 5216DACLiteRxx-LV.ZIP. Unzip the file and run the cable is not included, but is widely available from local setup.exe. Follow the instructions to install the evalua- stores. tion software on your PC. The program files are copied The EV kit is preloaded with the default firmware that and icons are created in the Windows Start Programs communicates with the MAX5216DACLite evaluation menu. Connect the MAX5216DACLite to the PC though software. Software can be installed and run on any a USB cable. No additional driver is needed Windows Windows-based system. recognizes the new device as a human interface device (HID) and automatically finds and installs the Digital multimeter (DMM) appropriate driver for it. For more information, check Note: In the following sections, software-related items are the device properties in: Device Manager Human identified by bolding. Text in bold refers to items directly Interface Control USB Input Device Properties from the EV kit software. Text in bold and underlined USB VID 0B6A&PID 1234. See Figure 1. refers to items from the Windows operating system. 2) Run the MAX5216DACLite. exe program. The applica- tions GUI appe ars, as shown in Figure 2. MAX is a registered trademark of Maxim Integrated Products, Inc. Maxim Integrated 2 www.maximintegrated.com