EVALUATION KIT AVAILABLE MAX8903AE/G/H/J/N/Y 2A 1-Cell Li+ DC-DC Chargers for USB and Adapter Power General Description Features Efficient DC-DC Converter Eliminates Heat The MAX8903AMAX8903E/MAX8903G/MAX8903H/ MAX8903J/MAX8903N/MAX8903Y are integrated 1-cell 4MHz Switching for Tiny External Components Li+ chargers and Smart Power Selectors with dual Instant OnWorks with No/Low Battery (AC adapter and USB) power inputs. The switch mode Dual Current-Limiting InputsAC Adapter or USB charger uses a high switching frequency to eliminate Automatic Adapter/USB/Battery Switchover to heat and allow tiny external components. It can operate Support Load Transients with either separate inputs for USB and AC adapter 50m System-to-Battery Switch power, or from a single input that accepts both. All Supports USB Spec power switches for charging and switching the load Thermistor Monitor between battery and external power are included on- Integrated Current-Sense Resistor chip. No external MOSFETs, blocking diodes, or cur- No External MOSFETs or Diodes rent-sense resistors are required. 4.1V to 16V Input Operating Voltage Range The MAX8903 features optimized smart power control to make the best use of limited USB or adapter power. Ordering Information Battery charge current and SYS output current limit are PART TEMP RANGE PIN-PACKAGE independently set. Power not used by the system charges the battery. Charge current and SYS output cur- MAX8903AETI+T -40C to +85C 28 Thin QFN-EP* rent limit can be set up to 2A while USB input current can MAX8903BETI+T -40C to +85C 28 Thin QFN-EP* be set to 100mA or 500mA. Automatic input selection MAX8903CETI+T -40C to +85C 28 Thin QFN-EP* switches the system from battery to external power. The MAX8903DETI+T -40C to +85C 28 Thin QFN-EP* DC input operates from 4.15V to 16V with up to 20V pro- tection, while the USB input has a range of 4.1V to 6.3V MAX8903EETI+T -40C to +85C 28 Thin QFN-EP* with up to 8V protection. MAX8903GETI+T -40C to +85C 28 Thin QFN-EP* The MAX8903 internally blocks current from the bat- MAX8903HETI+T -40C to +85C 28 Thin QFN-EP* tery and system back to the DC and USB inputs when MAX8903JETI+T -40C to +85C 28 Thin QFN-EP* no input supply is present. Other features include pre- MAX8903NETI+T -40C to +85C 28 Thin QFN-EP* qual charging and timer, fast charge timer, overvoltage MAX8903YETI+T -40C to +85C 28 Thin QFN-EP* protection, charge status and fault outputs, power-OK +Denotes a lead(Pb)-free/RoHS-compliant package. monitors, and a battery thermistor monitor. In addition, *EP = Exposed pad. on-chip thermal limiting reduces battery charge rate T = Tape and reel. and AC adapter current to prevent charger overheat- ing. The MAX8903 is available in a 4mm x 4mm, 28-pin Typical Operating Circuit thin QFN package. The various versions of the MAX8903 allow for design flexibility to choose key parameters such as system AC LX CS regulation voltage, battery prequalification threshold, ADAPTER OR USB DC SYS and battery regulation voltage. The MAX8903B/ MAX8903E/MAX8903G also includes power-enable on LOAD battery detection. See the Selector Guide section for CURRENT CHARGE complete details. CURRENT CHARGE SYSTEM Applications AND LOAD SYS LOAD PDAs, Palmtops, and Portable Multimedia PWM SWITCH STEP-DOWN Wireless Handhelds Players Personal Navigation Mobile Internet Devices BAT BATTERY USB USB Devices Ultra Mobile PCs Smart Cell Phones MAX8903 GND Selector Guide appears at end of data sheet. Smart Power Selector is a trademark of Maxim Integrated Products, Inc. Pin Configuration appears at end of data sheet. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxims website at www.maximintegrated.com. 19-4410 Rev 5 9/11MAX8903AE/G/H/J/N/Y 2A 1-Cell Li+ DC-DC Chargers for USB and Adapter Power ABSOLUTE MAXIMUM RATINGS DC, LX to GND .......................................................-0.3V to +20V LX Continuous Current (total in two pins).......................2.4A RMS DCM to GND ..............................................-0.3V to (V + 0.3V) CS Continuous Current (total in two pins) ......................2.4A DC RMS DC to SYS .................................................................-6V to +20V SYS Continuous Current (total in two pins) .......................3A RMS BST to GND ...........................................................-0.3V to +26V BAT Continuous Current (total in two pins) .......................3A RMS BST TO LX................................................................-0.3V to +6V VL Short Circuit to GND .............................................Continuous USB to GND .............................................................-0.3V to +9V Continuous Power Dissipation (T = +70C) A USB to SYS..................................................................-6V to +9V 28-Pin Thin QFN-EP VL to GND ................................................................-0.3V to +6V Multilayer (derate 28.6mW/C above +70C) ..........2286mW THM, IDC, ISET, CT to GND........................-0.3V to (V + 0.3V) 28-Pin Thin QFN-EP VL DOK, FLT, CEN, UOK, CHG, USUS, Single-Layer (derate 20.8mW/C above +70C)...1666.7mW BAT, SYS, IUSB, CS to GND ................................-0.3V to +6V Operating Temperature Range ...........................-40C to +85C SYS to BAT ...............................................................-0.3V to +6V Junction Temperature Range ............................-40C to +150C PG, EP (exposed pad) to GND .............................-0.3V to +0.3V Storage Temperature Range .............................-65C to +150C DC Continuous Current (total in two pins)......................2.4A Lead Temperature (soldering, 10s) .................................+300C RMS USB Continuous Current.......................................................1.6A Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (V = V = 5V, V = 4V, circuit of Figure 2, T = -40C to +85C, unless otherwise noted. Typical values are at T = +25C.) DC USB BAT A A (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS DC INPUT DC Operating Range 4.15 16 V No valid USB input 3.9 4.0 4.1 When V goes low, V DOK DC DC Undervoltage Threshold V rising, 500mV typical hysteresis Valid USB input 4.0 4.3 4.4 When V goes high, V rising, 500mV typical DOK DC DC Overvoltage Threshold 16.5 17 17.5 V hysteresis Charger enabled, no switching, V = 5V 2.3 4 SYS Charger enabled, f = 3MHz, V = 5V 15 DC DC Supply Current mA C har g er enabl ed, V = 0V , 100m A U S B mod e ( N ote 2) 1 2 C E N C har g er enab l ed, V = 5V , 100m A US B mod e ( N ote 2) 1 2 C E N V = 0V, V = 5V 0.10 0.25 DCM USUS DC High-Side Resistance 0.15 DC Low-Side Resistance 0.15 DC-to-BAT Dropout Resistance Assumes a 40m inductor resistance (R ) 0.31 L When SYS regulation and charging stops, V falling, DC DC-to-BAT Dropout Voltage 015 30 mV 200mV hysteresis Minimum Off Time (t ) 100 ns OFFMIN Minimum On Time (t ) 70 ns ONMIN V = 8V, V = 4V 4 DC BAT MAX8903A/B/C/D/E/H/J/Y V = 5V, V = 3V 3 DC BAT Switching Frequency (f ) MHz SW V = 9V, V = 4V 1 DC BAT MAX8903G V = 9V, V = 3V 1 DC BAT DC Step-Down Output Current- 0.5 2 A Limit Step Range R = 3k 1900 2000 2100 IDC DC Step-Down Output Current V = 6V, V = 4V R = 6k 950 1000 1050 mA DC SYS IDC Limit (I ) SDLIM R = 12k 450 500 550 IDC Maxim Integrated 2