EVALUATION KIT AVAILABLE MAX9259/MAX9260 Gigabit Multimedia Serial Link with Spread Spectrum and Full-Duplex Control Channel General Description Features S Ideal for Digital Video Applications The MAX9259 serializer pairs with the MAX9260 deseri- Up to XGA (1280 x 768) or Dual-View WVGA alizer for joint transmission of high-speed video, audio, (2 x 854 x 480) Panels with 18- or 24-Bit Color and control data. Pre/Deemphasis Allows 15m Cable at Full Speed The MAX9259/MAX9260 operate up to 3.125Gbps for a 2 Up to 192kHz, 32-Bit Sample I S 15m shielded twisted-pair (STP) cable. This serial link S Multiple Data Rates for System Flexibility supports display panels from QVGA (320 x 240) up to Up to 3.12Gbps Serial-Bit Rate XGA (1280 x 768), or dual-view WVGA (2 x 854 x 480). 6.25MHz to 104MHz Pixel Clock 2 The embedded audio channel supports I S up to 32 bits 2 Up to 1Mbps UART/UART-to-I C Control Channel per sample and at a 192kHz sample rate. The embed- S Reduces EMI and Shielding Requirements ded control channel forms a full-duplex, differential Serial Output Programmable for 100mV to 400mV 100kbps to 1Mbps UART link between the serializer and Programmable Spread Spectrum Reduces EMI deserializer. The host electronic control unit (ECU) or Bypasses Input PLL for Jitter Attenuation microcontroller (FC) resides either on the MAX9259 or on S Peripheral Features for System Verification the MAX9260. In addition, the control channel enables Built-In Serial Link PRBS BER Tester ECU/FC control of peripherals in the remote side of the Interrupt Transmission from Deserializer to 2 serial link through I C/UART. Serializer Preemphasis and channel equalization extend the link Meets AEC-Q100 Requirements length and enhance the link reliability. Spread spectrum -40NC to +105NC Operating Temperature Range is available to reduce EMI on the serial and parallel out- 10kV Contact and 25kV Air ISO 10605 and put data signals. The differential link complies with the 10kV IEC 61000-4-2 ESD Protection ISO 10605 and IEC 61000-4-2 ESD-protection standards. The core supplies for the MAX9259/MAX9260 are 1.8V Simplified Diagram and 3.3V, respectively. Both devices use an I/O sup- ply from 1.8V to 3.3V. These devices are available in a 64-pin TQFP package (10mm x 10mm) and a 56-pin VIDEO/AUDIO VIDEO/AUDIO TQFN/QFND package (8mm x 8mm x 0.75mm) with an exposed pad. Electrical performance is guaranteed over 720p the -40NC to +105NC automotive temperature range. C MAX9259 MAX9260 DISPLAY Applications 2 2 I C I C High-Resolution Automotive Navigation Rear-Seat Infotainment Ordering Information Megapixel Camera Systems PART TEMP RANGE PIN-PACKAGE MAX9259GCB/V+ -40NC to +105NC 64 TQFP-EP* MAX9259GCB/V+T -40NC to +105NC 64 TQFP-EP* MAX9259GTN/V+T -40NC to +105NC 56 TQFN-EP* MAX9259GGN/VY+ -40NC to +105NC 56 QFND-EP* MAX9260GCB/V+ -40NC to +105NC 64 TQFP-EP* MAX9260GCB/V+T -40NC to +105NC 64 TQFP-EP* /V denotes an automotive qualified part. +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. T = Tape and reel. Typical Applications Circuit appears at end of data sheet. For pricing, delivery, and ordering information, please contact Maxim Direct 19-4968 Rev 4 10/14 at 1-888-629-4642, or visit Maxims website at www.maximintegrated.com.MAX9259/MAX9260 Gigabit Multimedia Serial Link with Spread Spectrum and Full-Duplex Control Channel ABSOLUTE MAXIMUM RATINGS AVDD to AGND OUT+, OUT- Short Circuit to Ground or MAX9259 ...........................................................-0.5V to +1.9V Supply (MAX9259) .................................................Continuous MAX9260 ...........................................................-0.5V to +3.9V IN+, IN- Short Circuit to Ground or DVDD to GND (MAX9259) ...................................-0.5V to +1.9V Supply (MAX9260) .................................................Continuous DVDD to DGND (MAX9260) .................................-0.5V to +3.9V Continuous Power Dissipation (T = +70NC) A IOVDD to GND (MAX9259) ..................................-0.5V to +3.9V 64-Pin TQFP (derate 31.3mW/NC above +70NC) .......2508mW IOVDD to IOGND (MAX9260) ..............................-0.5V to +3.9V 56-Pin TQFN (derate 47.6mW/NC above +70NC) ....3809.5mW Any Ground to Any Ground .................................-0.5V to +0.5V 56-Pin QFND (derate 42.7mW/NC above +70NC) ......3148mW Operating Temperature Range ........................ -40NC to +105NC OUT+, OUT- to AGND (MAX9259) ......................-0.5V to +1.9V Junction Temperature .....................................................+150NC IN+, IN- to AGND (MAX9260) ..............................-0.5V to +1.9V Storage Temperature Range ............................ -65NC to +150NC LMN to GND (MAX9259) Lead Temperature (soldering, 10s) ................................+300NC (60kI source impedance) ................................-0.5V to +3.9V Soldering Temperature (reflow) ......................................+260NC All Other Pins to GND (MAX9259) .......-0.5V to (IOVDD + 0.5V) All Other Pins to IOGND (MAX9260) ...-0.5V to (IOVDD + 0.5V) PACKAGE THERMAL CHARACTERISTICS (Note 1) 64 TQFP 56 QFND Junction-to-Ambient Thermal Resistance (B ) .......31.9NC/W Junction-to-Ambient Thermal Resistance (B ) .......23.4NC/W JA JA Junction-to-Case Thermal Resistance (B ) .................1NC/W Junction-to-Case Thermal Resistance (B ) ..............1.6NC/W JC JC 56 TQFN Junction-to-Ambient Thermal Resistance (B ) ..........21NC/W JA Junction-to-Case Thermal Resistance (B ) .................1NC/W JC Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-lay- er board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. MAX9259 DC ELECTRICAL CHARACTERISTICS (V = V = 1.7V to 1.9V, V = 1.7V to 3.6V, R = 100I Q1% (differential), T = -40NC to +105NC, unless otherwise noted. DVDD AVDD IOVDD L A Typical values are at V = V = V = 1.8V, T = +25NC.) DVDD AVDD IOVDD A PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SINGLE-ENDED INPUTS (DIN , PCLKIN, PWDN, SSEN, BWS, ES, DRS, MS, CDS, AUTOS, SD, SCK, WS) 0.65 x High-Level Input Voltage V V IH1 V IOVDD 0.35 x Low-Level Input Voltage V V IL1 V IOVDD Input Current I V = 0 to V -10 +10 FA IN1 IN IOVDD Input Clamp Voltage V I = -18mA -1.5 V CL CL SINGLE-ENDED OUTPUT (INT) V IOVDD High-Level Output Voltage V I = -2mA V OH1 OH - 0.2 Low-Level Output Voltage V I = 2mA 0.2 V OL1 OL V = 3.0V to 3.6V 16 35 64 IOVDD Output Short-Circuit Current I V = 0V mA OS O V = 1.7V to 1.9V 3 12 21 IOVDD 2 Maxim Integrated