Crimp Tool TP0001 Anderson Power Products TP0001 pneumatic crimp tool offers versatility in crimping range and configurability in shop setup. The tool is compact and lightweight which allows it to be used as either a hand-held tool or setup on a bench with optional accessories. A unique 8 step machined steel block holds accurate calibration far longer than the usual adjustment screw method resulting in high output with less downtime. Features Designed with up to 8 die closures which can be changed by selector knob Allows the tool to be quickly configured to the appropriate die Highly configurable in the shop Compatible with most air compressors Can be used as a hand tool or combined with the multiple available Has a industry typical working air pressure of 80 120 PSI accessories for bench mounting Accommodates upper range Mil Standard turrets & Optional bench mount can be adjusted to virtually any angle positioners Provides ease of use and flexibility in configuration Tool can be used for crimping multiple connection solutions SPECIFICATIONS Size Accommodations Crimping Range Length (in) 10 Tool will accommodate all Turret Heads and Single Position Heads Contacts Size (AWG) 12 to 20 (mm) 254 relating to M22520/1-01 Mil Standard tool frame. (mm) 2.5 to 0.75 Width (in) 2.75 Wire Size (AWG) 12 to 26 (mm) 69.85 (mm) 2.5 to 0.45 Weight (pounds) 3.1 (N) 44.48 ORDERING INFORMATION Crimp Tool Turret APP Part APP Part Military Number Description Number Part Number Description TP0001 Pneumatic crimp tool TL0001 N/A Turret - PowerMod Pins, 12 - 24 AWG (4.0 - 0.25 mm) TA0001 Foot pedal for TP0001 TL0002 N/A Turret - PowerMod Sockets, 12 - 24 AWG (4.0 - 0.25 mm) TA0002 Air regulator/filter TL0003 M22520/1-02 Turret - Power Drawer contacts, 12, 16 & 20 AWG (4.0, 1.3 & 0.5 mm) TA0003 Bench mount TL0005 N/A Positioner - PPMX contact, 20 - 24 AWG (0.5 - 0.25 mm) TP0001 TA0001 TA0002 TA0003 Measurements in inches www.andersonpower.comCaution Do not crimp hardened objects as damage can occur to the tool or die. Anderson crimp specifications are valid only when used with Anderson terminals and tooling. The user of the tool is responsible for determining if the crimps produced meet the quality requirements of the application. Foot Valve Operation Attach foot valve between air supply and tool air inlet. Depress hand valve and lock in down position with set screw (A) using 1/16 hex Allen wrench. Checking the full cycle ratcheting mechanism The ratcheting mechanism can be checked for proper functioning by the following procedure. 1. Adjust the air line pressure to 15 p.s.i. 2. Using a size 20 AWG contact with a size 20 AWG wire, operate the tool until the indenters stop. The indenters will not reach the fully closed position and the contact will be locked in if the ratcheting mechanism is functioning properly. 3. To release the partially crimped contact, increase the air line pressure to 80-120 p.s.i. and operate. The tool will then complete the crimp allowing the indenters to return to the fully open position. Releasing a partially crimped contact To release a partially crimped contact, proceed as follows: 1. Increase the air pressure to 120 p.s.i. and operate the unit. If increasing the air pressure does not release the contact, proceed to step 2. 2. Turn the selector knob clockwise to the highest lockable setting. Selector knob must be in the locked position before proceeding. Cycle the unit. 3. If release has not been achieved after several attempts, contact the manufacturer to avoid damaging the tool. Care of Tool There is virtually no maintenance required. However, it is a good practice to keep indenter tips free of residual color band deposits and other debris. A small wire brush may be used for this purpose. We strongly recommend that you: DO NOT immerse tools in cleaning solution. DO NOT spray oil into tool to lubricate. DO NOT attempt to disassemble tool or make repairs. This is a precision crimping tool and should be handled as such. Contact manufacturer for repair and calibration services. All Data Subject To Change Without Notice 14919 1S6527 REV 01 HEADQUARTERS: Anderson Power Products, 13 Pratts Junction Road, Sterling, MA 01564-2305 USA T:978-422-3600 F:978-422-3700 EUROPE: Anderson Power Products Ltd., Unit 3, Europa Court, Europa Boulevard, Westbrook, Warrington, Cheshire, WA5 7TN United Kingdom T: +44 (0) 1925 428390 F: +44 (0) 1925 520203 ASIA / PACIFIC: IDEAL Anderson Asia Pacific Ltd., Unit 922-928 Topsail Plaza, 11 On Sum Street, Shatin N.T., Hong Kong T:+(852) 2636 0836 F:+(852) 2635 9036 CHINA: IDEAL Anderson Technologies (Shenzhen) Ltd., Block A8 Tantou Western Industrial Park, Songgang Baoan District, Shenzhen, PR. China 518105 T: +(86) 755 2768 2118 F: +(86) 755 2768 2218 TAIWAN: IDEAL Anderson Asia Pacific Ltd., Taiwan Branch, 4F.-2, No.116, Dadun 20th St., Situn District, Taichung City 407, Taiwan (R.O.C.) T: +(886) 4 2310 6451 F:+(886) 4 2310 6460 www.andersonpower.com