3000 series Premium Hall effect joysticks Distinctive features and specifications Class leading installed depth <20 mm Hall effect sensing 1, 2 or 3 axis 5V or 3.3V operation EMC shielded Analog or PWM outputs Next generation metal mechanisms Dual outputs available ELECTRICAL MECHANICAL Gain (Output Voltage Span): 10% x V to 50% x V Materials Employed: Shaft - Stainless Steel Output at Center: V/2 (5% x Gain) Boot - Neoprene Power Supply: 5V 0.5V Transient free Others - Brass, Nylon, ABS (Configs 1, 3, 4 & 5) or 3.3V 0.1V (Config 2) Weight: 100g (0.20lb) nominal Center Tap Impedance: 1K1 Breakout Force: 1.3N (2.86lbf) Center Detect Output: Pulled high within joystick Mechanical Angle of Movement: via 2K2 to +V, and smoothed to 0V with 100nF 36 for X and Y axis (subject to limiter) Sensor Type: Hall effect 50 for Z axis (subject to handle) Current Consumption: Max Load to Mechanism: 400N (881.85lbf) 5V <13mA (Two axis) <20mA (Three axis) NOTES: 3.3V <24mA (Two axis) <40mA (Three axis) Loads: Minimum 10K, preferred 100K+ 1. All values are nominal. 2. All specifications shown are based on a ENVIRONMENTAL standard configuration and are provided for guidance only. Operating Temperature: -25C to 70C (-13F to 158F) 3. Please refer to APEM for assistance on how Storage Temperature: -40C to 70C (-40F to 158F) to achieve the best performance from your Seal Above Panel: IP65 Neoprene boot fitted as standard chosen configuration. EMC Emission: Complies with EN 61000-6-3:2001, 4. Current consumption will be greater for CISPR 22:2005, Class B 30MHz11GHz dual output configurations. Life Cycles: 10,000,000 cycles (5,000,000 for 3 axis joysticks) ESD: Complies with EN61000-4-2 (extended) 8KV (20 contacts) & 15KV (20 air discharges) EMC Immunity: 100V/m, 80MHz-2.7GHz, 1KHz 80% sine wave modulation, EN 61000-4-3 (extended) Vibration: 100Hz 200Hz 0.13g /Hz, total 3.6gRMS (1 Hour in each of the three mutually perpendicular axis) Note: The company reserves the right to change specifications without notice. APEM www.apem.com3000 series Premium Hall effect joysticks Overview SERIES Gain Handle* Modifier 3 3000 10 10%xV BL Round 00 None 25 25%xV E Conical 20 Guided Feel 30 30%xV Q Skirted 40 40%xV AK Push Button 50 50%xV AL Third Axis * for more handles see next pages Configuration Limiter Bezel 1 Standard A Single Axis 0 None 2 3.3V Operation C Cross 4 Circular (below panel) 3 Dual Outputs D Diamond 6 Square (drop-in) 4 Inverse Dual Outputs R Round 7 Circular (drop-in) 5 PWM S Square X X Type STANDARD OPTION AVAILABILITY The following table shows which permutations of options are possible. ALL ALL CONFIGURATION CT CD AXES SUPPLY GAIN LIMITERS HANDLES BEZELS X Y Z 3.3V 5V 10 25 30 40 50 A C D R S X 1 2 3 4 5 Y+ Z- Z+ 62.00 (2.44) X- X+ Y- 35.80 (1.41) 3.20* 4.50 (0.13) (0.18) CABLES EXIT TO THE EAST WHEN VIEWED FROM ABOVE 20.00 (0.79) 35.80 (1.41) 38.50 (1.52) 42.00 (1.65) NOTES: 1. Dimensions are in mm/(inch). 2. The dimensions shown are for generic 3000 series with E type handle. For specific dimensions of this or any other configuration please refer to APEM. * 3000 series has slotted mounting holes - allows compatibility with mounting pitches of 32.25mm to 35.80mm. Note: The company reserves the right to change specifications without notice. www.apem.com APEM