CJN3NS013N Apem

CJ series Ergonomic multifunction joysticks Distinctive features and specifications Ergonomic and versatile design 1 and 2 axis configurations Sealed up to IP68 Redundant outputs available Available with CANbus and USB outputs Industry common mounting cutout and hole pattern MECHANICAL (FOR X AND Y AXIS) STANDARD PUSHBUTTON SWITCH CHARACTERISTICS/RATINGS Break Out Force: 5.6N (1.26lbf) Operating Force: 7.6N (1.70lbf) Max Current / Voltage Rating with Resistive Load: Maximum Applied Force: 649.4N (146lbf) 400mA 32VAC - 100mA 50VDC - 125mA 125VAC Mechanical Angle of Movement: 40 (20) Low Level: 10mA 30mV Expected Life: 10 million cycles (depending on the chosen switch) Material: Glass reinforced nylon Electrical Life: 1 million cycles 5A 28 VDC Lever Action (Centering): Spring centering resistive snap-action (depending on the chosen switch) Mechanical Life: 1 million cycles Environmental Seal: IP67 ENVIRONMENTAL Action: Momentary, pushbutton Operating Temperature: -40C to 70C (-40F to 158F) Operating Force: 7N3N (1.57lbf0.67lbf) Storage Temperature: -40C to 70C (-40F to 158F) Total Travel: 1.9mm (0.07in)0.3mm (0.01in) Sealing (IP): Up to IP68 EMC Immunity Level (V/M): IEC 61000-4-3:2006 CAN OUTPUT VERSION EMC Emissions Level: IEC 61000-4-8:2009 ESD: IEC 61000-4-2:2008 Supply Voltage Range (VDC): 6V to 35V CAN Versions: J1939, CANopen ELECTRICAL SENSOR Resolution: 1.22mV NOTES: Supply Voltage Range: 5.00V0.01V All values are nominal. Reverse Polarity Max: -10V Exact specifications may be subject to configuration. Overvoltage Max: 20V Contact Technical Support for the performance of your Output Impedance: 2 specific configuration. Return to Center Voltage Tolerance: 200mV initial Supply Current: 13mA per sensor Note: The company reserves the right to change specifications without notice. APEM www.apem.comCJ series Ergonomic multifunction joysticks Overview CJ SERIES Lower Face Buttons Operator Spring Output Options Additional Options Deadman Lever Tension N None 00 0V to 5V N None 2 A One switch in N None 0 Standard 01 0.5V to 4.5V V Voltage Regulator position A D Deadman Paddle 02 0.25V to 4.75V E Environmental Sealing* B One switch in 03 1V to 4V position B 04 0V to 5V - Sensor 1 C One switch in 0V to 5V - Sensor 2 center 05 0.5V to 4.5V - Sensor 1 W Two switches 0.5V to 4.5V - Sensor 2 X Custom 06 0.25V to 4.75V - Sensor 1 0.25V to 4.75V - Sensor 2 07 1V to 4V - Sensor 1 1V to 4V - Sensor 2 08 0V to 5V - Sensor 1 5V to 0V - Sensor 2 09 0.5V to 4.5V - Sensor 1 4.5V to 0.5V - Sensor 2 10 0.25V to 4.75V - Sensor 1 Limiter Plate Upper Face Buttons 4.75V to 0.25V - Sensor 2 S Square 11 1V to 4V - Sensor 1 0 None R Round 4V to 1V - Sensor 2 1 One X Slotted 13 USB 2 Two Y Slotted 14 Cursor Emulation 3 Three P Plus 15 CANbus J1939 4 Four D Diamond 16 CANopen 5 Five G Guided Feel Square XX Custom 6 Six H Guided Feel Round X Custom NOTES: 1. Contact Technical Support for custom options. 2. Not available on dual output. *Environmental sealing level available up to IP68. Dependent upon handle configuration. Mounting accessories. Standard hardware includes: 4 Phil. screws (6-32x7/8). LOWER FACE BUTTONS N A B C W Note: The company reserves the right to change specifications without notice. www.apem.com APEM