FR2A1U02A2A Apem

FR series Hall effect 3-position thumb controls Distinctive features and specifications Non-contact Hall effect technology Three position, ON-OFF-ON analog output 3 million lifecycles Submersible to 1m (3.28ft) per IP68 Choice of handle color Redundant outputs available ENVIRONMENTAL MECHANICAL Operating Temperature: -40 C to +85 C (-40 F to +185 F) Initial Actuation Force: 3 Storage Temperature: -40 C to +85 C (-40 F to +185 F) 260g Nominal into position 2 4 3 Sealing: Submersible to 1m per IP68 360g Nominal out of position 2 3 EMC Immunity Level: EN61000-4-3 Maximum Vertical Load: 200N 3 EMC Emissions Level: EN61000-6-3:2001 Maximum Horizontal Load: 150N ESD: EN61000-4-2 Mechanical Life: 3,000,000 full forward to full back ELECTRICAL MATERIALS Supply Voltage Range: 5.00V 0.01V Handle/Actuator: Glass filled nylon Reverse Polarity Max: 10V Body: Glass filled nylon Overvoltage Max: 20V Boot: Silicone Return to Center Voltage Tolerance (POS2): 2.50V 0.50V NOTE: All values are nominal. Output Voltage Tolerance at Full Travel/Detent Position (POS1, POS3): 0.25V FR A 1 Handle Termination SERIES Output Options Handle Color 0 None 1 22 AWG 25cm PTFE POS1/POS2/POS3 1 Black 1 Castle 2 28 AWG 25cm PTFE 01 0.25/2.5/4.75VDC 2 Red 2 Winged Hat 3 2.54mm (0.100 ) Pitch 02 0.5/2.5/4.5VDC 3 Yellow 3 Conical TE Connector 03 1.0/2.5/4.0VDC A Handle 1, 2, 3 4 2.54mm (0.100 ) Pitch 05 0.25/2.5/4.75VDC TE Connector with 0.25/2.5/4.75VDC wire harness 06 0.5/2.5/4.5VDC 0.5/2.5/4.5VDC 07 1.0/2.5/4.0VDC Mounting Options Operation Power Supply 1.0/2.5/4.0VDC U Single Axis 09 0.5/2.5/4.5VDC N None A Single 2 4.5/2.5/0.5VDC D Drop-in B Independent 10 0.25/2.5/4.75VDC R Rear Mount 4.75/2.5/0.25VDC A Drop-in and Rear Mount 11 1.0/2.5/4.0VDC NOTES: 4.0/2.5/1.0VDC Mounting accessories. Standard hardware includes: For the Drop-in option: 4 push in connectors, drop-in bezel and an O-ring. For the Rear mount option: 4 x 1/2 FH SS Phil Screws and a rear mount bezel. 1-1 Wires are thick, robust, and best suited for stand alone applications. 1-2 Wires are thin and best suited for tightly constrained wire routing. 2 Only available on dual output. Not available with Termination Options 3 or 4. 3 Force applied to the top of the castle cap. 4 All options are IP68 rated, however Drop-in mounting does not prevent panel ingress. Note: The company reserves the right to change specifications without notice. APEM www.apem.comFR series Hall effect 3-position thumb controls Overview INDEX NOTCH 90 FROM DIRECTION OF TRAVEL 50 POS 2 POS 1 POS 3 20.07 .790 (0.79) 14.12 .556 (0.556) 25.27 .995 (0.995) 254.00 10in (10.00) 22AWG 22AWG HANDLE OPTIONS 1. CASTLE 2. WINGED HAT 3. CONICAL 17.30 .681 17.17 18.36 (0.681) .676 .723 (0.676) (0.723) 20.35 19.84 18.67 .801 .735 (0.801) (0.781) (0.735) NOTE: Dimensions are in mm/(inch). Note: The company reserves the right to change specifications without notice. www.apem.com APEM