HF series Hall effect joysticks Distinctive features and specifications Connectorized housing Voltage regulator, 24V supply option Shallow mounting depth <1.00 USB 2.0 HID interface options 1, 2 and 3 axis configurations CAN bus J1939 and CANopen options MECHANICAL (FOR X, Y AXIS) ENVIRONMENTAL Break Out Force: 1.3N (0.3lbf) Operating Temperature: -40C to 85C (-40F to 185F) Operating Force: 2.8N (0.63lbf) Storage Temperature: -40C to 85C (-40F to 185F) Maximum Applied Force: 200N (45.00lbf) Sealing (IP): Up to IP67* Mechanical Angle of Movement: 36 EMC Immunity Level (V/M): EN61000-4-3 (18 from center) EMC Emissions Level: EN61000-6-3:2001 Expected Life: 5 million ESD: EN61000-4-2 Material: Glass filled nylon Output linearity: 200mV Package Size: 5.75 x 4.50 x 3.25 Dual output interlinearity (X/Y): 400mV Lever Action: Single spring, omnidirectional Dual output interlinearity (Z): 600mV MECHANICAL (FOR Z AXIS) SENSOR SPECIFICATIONS Break Out Torque: 0.09Nm (0.80lbf in) Sensor: Hall effect, single or dual Operating Torque: 0.121Nm(1.07lbf in) Supply Voltage Range: 5VDC 0.01VDC Maximum Allowable Torque: 2.50Nm(22.13lbf in) Supply Current: 40mA typical / 50mA max (3 axis) Hand Mechanical Angle: 60 (30 from center) Reverse Polarity Max: -10VDC Handle Action: Spring centering, rotational Transient Overvoltage Max: 16VDC Expected Life: 5 million Ratiometric Output Voltage: See options Output Current: 8mA Output Load: 1K ohm min. Output Impedance: 2 NOTES: All values are nominal. Exact specifications may be subject to configuration. Contact Technical Support for the performance of your specific configuration. * Excludes some handle options. Note: The company reserves the right to change specifications without notice. APEM www.apem.comHF series Hall effect joysticks Overview HF SERIES Output Options Limiter Plate 0 0V to 5V S Square 1 0.5V to 4.5V R Round 2 0.25V to 4.75V X Slotted 3 1V to 4V Y Slotted 4 0V to 5V - Sensor 1 P Plus 0V to 5V - Sensor 2 C Cross 5 0.5V to 4.5V - Sensor 1 W Guided Feel Square 0.5V to 4.5V - Sensor 2 Z Guided Feel Round 6 0.25V to 4.75V - Sensor 1 0.25V to 4.75V - Sensor 2 Handle Mounting 7 1V to 4V - Sensor 1 1V to 4V - Sensor 2 10 Ball Tip (2 Axis) 1 Drop-in 8 0V to 5V - Sensor 1 11 Tapered (2 Axis) 4 Rear Mount * 5V to 0V - Sensor 2 22 1 Pushbutton (2 Axis) 9 0.5V to 4.5V - Sensor 1 27 1 Pushbutton (2 Axis), IP67 Sealed * Rear mount 4.5V to 0.5V - Sensor 2 33 3 Axis, not available 10 0.25V to 4.75V - Sensor 1 with handle 55 44 1 Pushbutton (3 Axis) 4.75V to 0.25V - Sensor 2 45 2 Pushbuttons (3 Axis) 11 1V to 4V - Sensor 1 46 Low Profile (3 Axis), 4V to 1V - Sensor 2 50 3 Axis, IP67 Sealed 0U USB-Horizontal, Mini B termination 51 3 Axis, 1 Pushbutton, IP67 Sealed 2U USB-Vertical cable exit 52 3 Axis, 2 Pushbutton, IP67 Sealed 1J Cursor Emulation 55 3 Axis, 2 Pushbutton, IP67 Sealed 0V 0V to 5V (Voltage regulator)* BV 10V (Voltage regulator)** 2C CAN bus J1939 3C CANopen NOTES 1. The HF Series joysticks are supplied with a Hirose DF11-12DP-2DS9(24) connector (male receptacle). (Fig 1) Cable not included. Please request at order entry. Cable connector (female socket) is Hirose DF11-12DS-2C. (Fig 2) Connector specifications: 12 position 2mm pitch dual row (2x6) pin header. Wire Color Description * Requires operating voltage 6V 35V ** Requires operating voltage 11V 35V Black Ground Red Power Blue/White X-Axis (Dual Output) Blue X-Axis Yellow/Black Y-Axis (Dual Output) Yellow Y-Axis Green/Black Z-Axis (Dual Output) Green Z-Axis Orange Button 1 White Button Common Violet Button 2 Fig 1 Fig 2 Up to IP67 available. Mounting accessories. Standard hardware includes: gasket, clamping ring, and four 4-40x3/4 Phil Ph MS SS screws. 2 Output voltage is ratiometric to supply voltage 3 Cable length is 6 from side of joystick to USB connector 4 Cable length is 7 from side of joystick to USB connector Note: The company reserves the right to change specifications without notice. www.apem.com APEM