REVISIONS
LTR DESCRIPTION DATE APPROVED
A Added ebanol and nickel plate finishes. 12 JUN 1989 Randy Larson
Editorial changes throughout.
B Updated referenced documents and contact
information. Technical and editorial 14 SEP 2001 Thomas Hess
changes throughout.
PREVIOUS CAGE CODE 14933 SUPERSEDED BY 037Z3.
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
Prepared in accordance with MIL-STD-100 Selected item drawing
REV
PAGE
REV
PAGE
B B B B B B B B B B B B B B
REV STATUS REV
OF PAGES
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PAGES
PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS
James B. Walker Jr.
COLUMBUS, OH
Original date of CHECKED BY TITLE
drawing
Ken Beymer
HOLDER, ELECTRICAL CARD, CARD GUIDE-
23 October 1988
RETAINER, SCREW ACTUATED, METAL
APPROVED BY
D. E. Morgan
SIZE CODE IDENT. NO. DWG NO.
A
14933
88052
REV B PAGE 1 OF 14
AMSC N/A 5998-E033
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1. SCOPE
1.1 Scope. This drawing describes the requirements for a family of lever actuated card guides intended for use with printed circuit
boards and circuit card assemblies in moderate shock and vibration environments.
1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows:
88052 -XXX E
Drawing Dash number Housing finish
number (see table I) (see 3.2.1)
2. APPLICABLE DOCUMENTS
2.1 Government documents.
2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this
document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the
Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2).
SPECIFICATIONS
FEDERAL
QQ-N-290 - Nickel Plating ((Electrodeposited).
QQ-P-416 - Plating, Cadmium (Electrodeposited).
DEPARTMENT OF DEFENSE
MIL-F-495 - Finish, Chemical, Black, for Copper Alloys.
MIL-S-5002 - Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapon Systems.
MIL-DTL-13924 - Coating, Oxide, Black, For Ferrous Metals.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-1285 - Marking of Electrical and Electronic Parts.
(Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the
Document Automation and Production Service (DAPS), Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA
19111-5094.)
2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless
otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the
solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the
solicitation (see 6.2).
AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
ASTM A366 - Standard Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent),
Cold-Rolled.
ASTM A582 - Standard Specification for Free-Machining Stainless Steel Bars.
ASTM B194 - Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar.
(Application for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West
Coshohocken, PA 19428-2959.)
DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO.
14933 88052
COLUMBUS, OHIO
A
REV B PAGE 2