11 October 2013 Page 1 FEATURES 26W Constant Current LED Driver LEDWC-026 Series High Efficiency (Up to 86%) Active Power Factor Correction (Typical 0.95) IP66 p RoHS Compliant Short Circuit Protection Approved to UL8750 & EN61347 Safety Standards Class 2 Output (Some models) & SELV SPECIFICATIONS Model Rated Voltage No Load Efficiency Current (11) Range Voltage (5) LEDWC-026S035PS (4,8) 350mA 38~75Vdc 85Vdc 86% LEDWC-026S045PS (5,8) 450mA 28~56Vdc 59Vdc 85% LEDWC-026S070PS (6,8) 700mA 19~37Vdc 42Vdc 85% LEDWC-026S105PS (7,8) 1050mA 13~25Vdc 32Vdc 84% LEDWC-026S140PS (7,8) 1400mA 10~19Vdc 26Vdc 82% LEDWC-026S175PS (7,8) 1750mA 8~15Vdc 22Vdc 81% Rated Power 26W Output Ripple 25% Io Line Regulation 1% Load Regulation 3% Overshoot/Undershoot 10%Io Turn On Delay (Typ.) 0.6s Measured at 120Vac Input / 0.3s Measured at 220Vac Input Voltage Range 90~305Vac Frequency Range 47Hz~63Hz Inrush Current 40A 220Vac Input 25C Cold start, Duration=100s, 10%Ipk-10%Ipk Leakage 0.75mA at 277Vac 60Hz input PF 0.96 120Vac / 0.95 220Vac AC Current (Typ.) 0.4A / 100Vac 0.2A /220Vac THD 20% at 100Vac-277Vac, 75%load-100%load Short Circuit Hiccup mode, no damage shall occur and the power supply shall restart when the fault condition is removed Temperature Range Operational -40C~70C (see derating curve) Storage -40C~85C Humidity Operational 10%~100%RH Storage 5%~100%RH Safety Standards UL8750, UL1012, UL1310, Class 2, CSA-C22.2 No. 107.1, CSA C22.2 NO.223-M91 Class 2 Conducted & EN55015 Class B Radiated EMI Harmonic Current EN 61000-3-2 EMS EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547 MTBF 200,000 hours (Measured at 120Vac Input, 80% load and 25C ambient temperature (MIL-HDBK-217F) Life Time 91,000 hours (measured at 120Vac input, 80% load and 60C case temperature Dimensions (L*W*H) 78*80*27 mm 3.07*3.15*1.06 inches Weight 200g Notes: Autec Power Systems Tel: (805)522-0888 www.autec.com 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 Others Safety & Environment Prote Input Output EMC al ctions 11 October 2013 Page 2 Notes: 1. Measured at full load and 220Vac Input. 2. The suffix may be changed to D to omit the dimming function and remove the three wires associated with that function 3. A suffix xxx may be added to denote variations or modifications to the base product, where x can be any alphanumeric character or blank. 4. Non-Class 2 output (USR & NCR) 5. Class 2 output (USR), Non-Class 2 output (CNR) 6. Class 2 output (USR), Class 2 output (CNR) only for wet location. 7. Class 2 output (USR & CNR) for wet location. 8. SELV Mechanical Specifications Autec Power Systems Tel: (805)522-0888 www.autec.com 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777