102-02 Avid

POWER LED: SYSTEM MONITORING: Wireless power present VBRIDGE: (7 - 14V Typ.) (Blue Solid) Receiver DC Bridge Voltage Wireless power removed (OFF) COMM. (0 - 3.3V Logic) Quick Start Guide Modulation Signal STATUS LED: Output power good 5V, 0-1A OUTPUT: (Green Solid) Internal load is disabled Output power good when external load (>0.25W) External load detected is connected. Internal load disabled (Amber Solid) CONFIGURATION SWITCHES: Test complete. Expecting transmitter to end power transfer (See reverse for all settings) (Red Solid) TEST Switch 1, Position 1-6 Selects functional tests ERROR BLINK PATTERNS: LOAD Switch 2, Position 1-4 Selects internal load 0-2W, in 0.25W Steps Over temperature (Red Single Blink Pattern) COMM Switch 2, Position 5-6 Selects modulator type Output overload (Red Double Blink Pattern) TEST and COMM. settings are latched only at power-up. Input over voltage wirelesspower avid-tech.com LOAD setting can be changed (Red Triple Blink Pattern) www.avid-tech.com during run time. 2011 AVID Technologies, Inc. All rights reserved. 99000009 Rev.A Sends invalid WPC spec. TEST Switch Settings LOAD Switch Settings 20 010100 version (v0.1) Default WPC Receiver (min. 0 0 000000 0000 0.00 W internal load Sends a reserved packet in messages in Config. Phase) 21 010101 Config. Phase Comm. Data Bit Rate 1 0001 0.25 W internal load Sends reserved packets in 22 010110 1 000001 Comm. data bit rate (-30 %) Power Transfer Phase 2 0010 0.50 W internal load 2 000010 Comm. data bit rate (-10 %) Requests invalid Power Ctrl. 23 010111 Hold-off Time (210ms) 3 000011 Comm. data bit rate (-4 %) 3 0011 0.75 W internal load End Power Transfer (EPT) 4 000100 Comm. data bit rate (+4 %) First message sent is 24 011000 5 000101 Comm. data bit rate (+10 %) 4 0100 1.00 W internal load EPT: Charged 6 000110 Comm. data bit rate (+30 %) 25 011001 EPT: Battery Fault * 5 0101 1.25 W internal load Packet Timing Invalid time between 26 011010 EPT: Charged * 7 000111 6 0110 1.50 W internal load messages in Config. Phase 8 001000 Sends 1st CEP late 27 011011 EPT: Internal Fault * 7 0111 1.75 W internal load 9 001001 Sends 2nd CEP late 10 001010 Sends CEP at min. intervals 28 011100 EPT: No Response * 8 1000 2.00 W internal load Requests 50ms Power Ctrl. 11 001011 Hold-off Time 29 011101 EPT: Over Current * 9 - 15 Reserved Packet Data / Order 12 001100 Sends no comm. packets 30 011110 EPT: Over Temperature * Sends no Rectified Power 13 001101 Packets 31 011111 EPT: Over Voltage * COMM Switch Settings Sends invalid checksum in all 14 001110 messages 32 100000 EPT: Reconfigure * 0 00 Capacitive AC modulator Sends invalid checksum in ID 15 001111 Message only 33 100001 EPT: Unknown * 1 01 Resistive AC modulator Sends proprietary packet first 16 010000 Misc. Tests instead of Signal Strength 2 10 Resistive DC modulator Sends only negative error 34 100010 17 010001 ID Message not sent packets 3 11 Reserved Sends Power Ctrl. Holdoff 35 63 Reserved 18 010010 Msg. after Config. Msg. Sends maximum optional 19 010011 * Message sent 2 sec. after power transfer starts. messages in Config. PhaseX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for avid manufacturer: Other Similar products are found below : 102-02 102-01 AES-ACC-WHIZZ-USB3 AES-ACC-MAAX-DISP1 AES-ACC-U96-4APWR