rBOX610 Robust RISC-based DIN-rail Fanless Embedded System with iMX-287 Processor, 4 COM, 2 CAN Bus and DIO Features Fanless design RISC-based module (iMX-287) processor 128MB DDR2 SDRAM onboard Wireless LED indicators (power, alarm, ready/active, COM, wireless) (3G/GPRS) 4GB eMMC onboard Completed Industrial AP development software (Serial server, RISC-based Module Modbus gateway, SNMP, Remote manager) (iMX-287) Processor 12-48 VDC wide range power input with terminal block Ready-to-run embedded Linux operating system Wide operating temperature range from -40C to +70C 4 COM Front view Console port DIO (4-In/4-Out) 2 CANBus SDHC slot Power DC-In SIM sot Fanless Low Power DIN-rail kit Freescale i.MX287 EN60950 Isolation IP40 Ext. Temp UL508 Rear view Easy-to-access interface Introduction System I/O Outlet USB 1 x USB 2.0 The rBOX610 cost-effective DIN-rail fanless embedded system utilizes the low power USB power distribution control by RISC-based module (iMX-287) processor and is designed to withstand temperatures software ranging from -40C to +70C for using in extreme operating environment and industrial CAN 2 CAN 2.0 B (Phoenix connector, non- automation applications. isolation) Meets ISO 11898 standard The rBOX610 features 4 RS-232/422/485 serial ports, dual LANs, 4 digital input channels, Software control termination resistor 4 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket for storage expansion (easy to access) in a compact, IP40 protected, industrial-strength 120 ohm can high speed up to 1Mbit/s for transmit/receive robust case. Two power paths input minimize the risk of data loss in the event of a single power failure. Its vertical DIN-rail form factor makes it easy to install the system in a DIO 1 x DIO (4-IN/4-OUT) small cabinet. Due to the RISC-based architecture, rBOX610 will not generate a lot of DI: heat while being operated. The ready-to-run the rBOX610 is specially designed for remote Input channels : 4, source type control/monitoring management applications like unmanned control room, industrial Input voltage : 0 to 30 VDC digital input machine, automatic parking lot, traffic cabinet and more. levels for dry contacts: -Logic level 0: close to GND -Logic level 1: open Digital input levels for wet contacts: -Logic level 0: +10V to +24V (DI to COM-) Hardware Specifications -Logic level 1: +3V max. DO: Standard Color Sliver-Black Output channels: 4, sink type Construction Extruded aluminum and heavy-duty steel, IP40 Output current: max. 200 mA per channel CPU i.MX287, ARM926EJ-S processor, 454MHz On-state voltage : 24 VDC nominal, open System Board Q7M100 collector to 30 V System Memory 1 x DDR2-667 SDRAM onboard, 128MB Optical isolation protection 2 KV System I/O Outlet Serial Port 4 x RS-232/422/485 (COM 1 ~ 4) Console Port DB9 connector COM 1~3 with TX/RX/RTS/CTS signals For user setting with debug RS-232/422/485 interface select by RTC Battery onboard software Provides power for the internal real time LAN 2 x 10/100 Mbps Ethernet clock & calendar Magnetic isolation protection 1.5KV Ideal for vibration environment & reduces maintenance efforts Alarm Contact One relay output with current 0.5A 30 VDC 365 * All specifications and photos are subject to change without notice.DIN-rail Embedded Systems Hardware Specifications Software Specifications System I/O Outlet Wireless 1 x Mini Card (supports USB interface on OS: Linux Host OS/ Development OS : Ubuntu 10.04 Yocto Toolchain/ Cross compiler : Freescale LTIB 3G/GPRS) Kernel : 2.6.35.3 (with Freescale and Axiomtek hardware 1 x SIM socket by outside access and is modified patch) easy plug/pull Watchdog Timer WDT 1: one step is 1 sec, 255 levels Support protocol types ICMP. TCP/IP, LEDs System Power, Alarm, Ready/Active, COM UDP,DHCP,Telnet,SNMP,HTTP,HTTPS,SSL,SMTP,ARP, (TX, RX), Wireless NTP,DNS,PPP,PPPOE,FTP.TFTP Alarm DC PWR1 or PWR2 is lost Support software types Serial Server: Storage 1 x eMMC 4 GB onboard (for boot disk) Supports TCP Server/TCP Client/UDP/Pair/VC Supports 1 x SDHC Card (easy-to-access, for store only.) Supports IP filter Installation DIN-rail, wall mount Supports 32 TCP connections Power Supply Power Input 2 power paths with terminal block Supports QOS Power Input Range 12-48 VDC Modbus gateway: Power Input Rating 12-48 VDC, 0.68-0.19A Supports Modbus TCP/Modbus RTU/Modbus ASCII Supports IP filter Power Protection DC Version: 0 Supports 32 connections OVP (Over voltage protection) Supports TCP for multiple com port UVP (Under voltage protection) Supports QOS Reverse protection Setting configuration SNMP: Operating Temperature -40C ~ +70C (-40F ~ +158F) 1 Supports V1/V2C/V3 Humidity 5% ~ 95% Supports SNMP Private MIB Vibration Endurance 5G 10-150Hz, amplitude 0.35ms Supports read/write Weight (net/gross) 1.0 kg (2.2 lb)/1.50 kg (3.3 lb) http /https: Dimensions 55 mm (2.16 ) (W) x 155 mm (6.10 ) (D) x 110 mm (4.33 ) (H) 2 Supports SSL OS Linux Linux (Pre-installed) Supports Import/export Certificate FCC Part 18 Supports FW update Heavy Industrial CE Remote Manager Remote Log Email 3 SNMP Supports Trap Serial Port Redirector for XP/2003 32-64/Win7 32-64/Vista 32-64/2008 32-64 Ordering Information window Real com (visual com) 4 Standard Centralized management rBOX610-FL-DC Robust DIN-rail fanless embedded system with Q7-RISC Import/Export for real com module (iMX-287), 4 COM, 2 CAN and DIO HWs lib DI/DO: (-40C ~ +70C) Supports Read-DI/write DO 5 CAN: Optional Supports Open/write /read/Close Wall mount kit 3G: Wireless (3G/GPS or Wi-Fi) module for rBOX series Supports setting number connection 6 Supports User name/password Supports detecting signal strength Dimensions GPS: Supports detecting signal strength 7 Supports satellite positioning Watch Dog Timer: Supports setting enable Supports setting clean 8 Supports setting timer COM: Supports setting RS-232/422/485 Default Reading: Supports default reading for MAC, IP, Model 9 10 11 axiomtek.com 366 * All specifications and photos are subject to change without notice. 2017 Axiomtek Co., Ltd. All rights reserved.