D10 Expert Dual Discrete Outputs Advanced sensor for use with plastic fiber optics Features Easy-to-set automatic Expert-style TEACH options* including static, dynamic, and single-point programming plus manual adjustment for fine-tuning 16-bit microcontroller and 12-bit Analog-to-Digital converter for high-performance, low-contrast sensing Easy-to-read 4-digit display for TEACH and signal strength readout, plus indicators for a continuous readout of operating status (user configurable) Two discrete outputs, PNP or NPN Four-mode power and speed selection with automatic cross-talk avoidance circuitry Selectable OFF-delay options Gate input wire can be used to selectively inhibit sensor outputs from switching Models available with visible red (680 nm) or visible green (525 nm) sensing beam Models available with 2 m or 9 m (6.5 or 30 ) cable or integral Pico-style quick-disconnect Sleek, ultra-slim 10 mm housing, mounts to a standard 35 mm DIN rail * U.S. Patent 5,808,296 Models Models Cables* Discrete Outputs Red Beam Green Beam D10DNFP D10DNFPG 2 m (6.5 ) Cable NPN D10DNFPQ D10DNFPGQ 6-pin Pico-style QD D10DPFP D10DPFPG 2 m (6.5 ) Cable PNP D10DPFPQ D10DPFPGQ 6-pin Pico-style QD * 9 m (30 ) cables are available by adding suffix W/30 to the model number of any cabled sensor (e.g., D10DNFP W/30). A model with a QD connector requires a mating cable (see page 14). WARNING . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. Printed in USA 03/09 P/N 64154 rev. F D10 Expert Dual Discrete Outputs For emitter and receiver port Overview locations, see page xx. Output The D10 Expert Sensor is a high-performance plastic fiber-optic sensor whose many Indicators configuration (TEACH-mode) options make it suitable for demanding applications. Even with Output Select all its features, it is extremely easy to use. Advanced 16-bit microcontroller technology makes Indicators this possible. 4-Digit The D10 Expert provides high-performance sensing in low-contrast applications. Expert Display TEACH and setup options provide static, dynamic and single-point programming plus manual Light/Dark fine adjustment, remote programming and push button lockout. Its slender, stylized housing Operate, Clock dynamic has a large digital display visible beneath a clear cover for easy programming and status and Lock Icons monitoring during operation. The sensor mounts directly to standard 35 mm DIN rail or using Programming the supplied mounting bracket. Push Buttons The sensor features two outputs with independent setpoints: either NPN or PNP, depending static on model. Built-in crosstalk avoidance protocol provides trouble-free operation for multiple sensors in one area. Figure 1. D10 features Light/Dark Toggle to select the condition for which each output will conduct: when the target is present or when the target is absent. Operate Selection OFF-Delay Timing Programmable OFF-delay pulse stretcher: 0, 2, 5, 10, 15, 20, 30, 40, 60, 80, or 100 milliseconds Selection Discrete Output: Raw signal value or % excess signal Display Selection Power Level/ Super High-Speed (SHS) High-Speed (HS) High-Power (HP) Super High-Power (SHP) Speed Selection Response* 50 s 200 s 1 ms 2.5 ms Repeatability 25 s 50 s 75 s 100 s Fiber Red 680 nm Green 525 nm Red 680 nm Green 525 nm Red 680 nm Green 525 nm Red 680 nm Green 525 nm PIT16U 20 mm 9 mm 30 mm 9 mm 55 mm 13 mm 90 mm 16 mm 100 mm 40 mm 150 mm 40 mm 250 mm 55 mm 400 mm 70 mm PIT26U 300 mm 100 mm 550 mm 100 mm 1000 mm 160 mm 1200 mm 180 mm PIT46U 600 mm 180 mm 1000 mm 180 mm 1700 mm 280 mm 2400 mm 320 mm PIT66U 6 mm ** 10 mm ** 18 mm 3 mm 30 mm 3.5 mm PBT16U PBT26U 30 mm 12 mm 50 mm 12 mm 100 mm 20 mm 150 mm 25 mm PBT46U 100 mm 30 mm 175 mm 30 mm 250 mm 42 mm 300 mm 60 mm 175 mm 55 mm 250 mm 55 mm 400 mm 80 mm 475 mm 100 mm PBT66U Sets Output 2 to identical settings as Output 1 Output 2 settings can then be revised as desired. (See Advanced Setup procedure, page 11.) Tracking Feature The following settings are preset at the factory revert sensor to factory defaults using Advanced Setup procedure (page 11). Factory Default Light operate (LO) Output 1 displayed Maximum power setting Settings No OFF-delay (t 0) High Speed (HS) 200 s response Discrete: switchpoint positioned at middle of range Raw signal value (1234) * Diffuse mode performance based on 90% reflectance white test card. ** 0.010 bifurcated fiber not recommended in these speed settings. Contact Banner Applications for more information. See note on page 10. Banner Engineering Corp. Minneapolis, MN U.S.A. www.bannerengineering.com Tel: 763.544.3164 2 P/N 64154 rev. F Maximum Range*