SM30PRL Banner

SM30 Series 30 mm Barrel Sensor Opposed-Mode Infrared Photoelectric Sensors for Especially Demanding Applications Stainless steel or plastic barrel models Very high excess gain 150 m (500 ft) sensing range 880 nm Infrared LED Positive sealing eliminates even capillary leakage lens is quad-ring sealed exceeds NEMA 6P (IP67) ratings ideal for equipment wash-down environments EZ-BEAM technology provides reliable sensing without the need for adjustment Modulation frequency A is standard frequencies B and C also available for preventing crosstalk in multiple-sensor applications (emitter and opposed receiver frequencies must match) AC- and DC-operated receiver models available emitters feature Universal voltage Range for all models: 150 m (500 ft). See page 3 for performance curves. Modulation Frequency* Supply Housing Cable** Output Type Power A B C Emitter Models SMA30PEL SMA30PELB SMA30PELC 2 m (6.5 ) 2-wire Cable Plastic Universal: SMA30PELQD SMA30PELQDB SMA30PELQDC 3-pin Mini-style QD 12 to 240V ac, SMA30SEL SMA30SELB SMA30SELC 2 m (6.5 ) 3-wire Cable Stainless 10 to 30V dc Steel SMA30SELQD SMA30SELQDB SMA30SELQDC 3-pin Mini-style QD DC Receivers SM30PRL SM30PRLB SM30PRLC 2 m (6.5 ) 4-wire Cable Plastic SM30PRLQD SM30PRLQDB SM30PRLQDC 4-pin Mini-style QD Bi-Modal 10 to 30V dc NPN or PNP SM30SRL SM30SRLB SM30SRLC 2 m (6.5 ) 4-wire Cable Stainless Steel SM30SRLQD SM30SRLQDB SM30SRLQDC 4-pin Mini-style QD AC Receivers SM2A30PRL SM2A30PRLB SM2A30PRLC 2 m (6.5 ) 2-wire Cable Plastic SPST SM2A30PRLQD SM2A30PRLQDB SM2A30PRLQDC 3-pin Mini-style QD Solid-state, SM2A30SRL SM2A30SRLB SM2A30SRLC 2 m (6.5 ) 3-wire Cable Stainless L.O. Steel SM2A30SRLQD SM2A30SRLQDB SM2A30SRLQDC 3-pin Mini-style QD 24 to 240V ac SM2A30PRLNC SM2A30PRLNCB SM2A30PRLNCC 2 m (6.5 ) 2-wire Cable Plastic SPST SM2A30PRLNCQD SM2A30PRLNCQDB SM2A30PRLNCQDC 3-pin Mini-style QD Solid-state, SM2A30SRLNC SM2A30SRLNCB SM2A30SRLNCC 2 m (6.5 ) 3-wire Cable D.O. Stainless Steel SM2A30SRLNCQD SM2A30SRLNCQDB SM2A30SRLNCQDC 3-pin Mini-style QD * Any emitter and receiver shown here can be used together, if they have the same modulation frequency. ** Standard 2 m (6.5 ft) cable and integral QD models are listed. A model with a QD connector requires a mating cable see page 4. To order the 9 m (30 ft) cable: add suffix W/30 following the Frequency suffix of any cable model (e.g., SM30PRLBW/30). AC models with QD require SM30CC model cables see page 4. WARNING . Not To Be Used for Personnel Protection Never use these products for personnel protection. Doing so could lead to serious injury or death. These devices do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A device failure or malfunction can cause either an energized or de-energized output condition. Consult your current Banner Safety Products catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection. Printed in USA Apr 2013 P/N 03541 Rev. ESM30 Series 30 mm Barrel Sensor Specifications Supply Voltage and Current Emitters: 12 to 240V ac (50/60 Hz) or 10-30V dc at 20 mA, 10% maximum ripple DC Receivers: 10 to 30V dc at 10 mA maximum (exclusive of load) 10% maximum ripple AC Receivers: 24 to 240V ac (50/60 Hz) Protected against reverse polarity and transient voltages Supply Protection Circuitry DC Receivers: Bi-Modal output (PNP sourcing or NPN sinking). Selection of light/dark operate and sourcing or Output Configuration sinking configuration dependent on hookup. AC Receivers: SPST solid-state switch light operate (LO) or dark operate (DO) dependent on model. Output Rating DC Receivers: 250 mA continuous Output saturation voltage (PNP & NPN configuration) < 1 volt at 10 mA and < 2 volts at 250 mA Off-state leakage current < 10 microamps AC Receivers: Maximum steady-state load capability is 500 mA Inrush capability: 10 amps for 1 second (non-repeating) Off-state leakage: current < 1.7 mA rms On-state voltage drop: < 3.5 volts rms across a 500 mA load < 5 volts rms across a 15 mA load Output Protection Circuitry Outputs of dc receivers are short circuit protected Output Response Time 10 milliseconds on/off Repeatability A frequency models: 1 ms B frequency models: 1.5 ms C frequency models: 2.3 ms Internal red LED, visible through the lens or from side of the sensor. Indicators Emitters: Red Power ON indicator LED DC Receivers: Lights whenever receiver sees its modulated light source AC Receivers: Lights whenever receivers output is conducting Construction Fully epoxy-encapsulated tubular threaded housing, positive sealed at both ends, quad-ring sealed acrylic lens. Plastic models: 30 mm diameter thermoplastic polyester housing and jam nuts. Stainless Steel models: 30 mm diameter 303 stainless steel housing and jam nuts. Exceeds NEMA 6P and IEC IP67 standards Environmental Rating PVC-jacketed 2 m or 9 m cables or Mini-style quick-disconnect (QD) fitting are available. QD cables are ordered Connections separately. See page 4. Operating Conditions Temperature: -40 to +70 C (-40 to +158 F) Relative humidity: 90% at 50 C (non-condensing) Certifications Dimensions Cabled Models QD Models Jam Nuts Jam Nuts (2 Provided) (2 Provided) Alignment Alignment Indicator (Receivers) Indicator (Receivers) M30 x 1.5 M30 x 1.5 Thread Thread 102 mm 114 mm (4.5 ) (4.0 ) Banner Engineering Corp. Minneapolis, MN U.S.A www.bannerengineering.com Tel: 763.544.3164 2 P/N 03541 Rev. E