SM30 Series EZ-BEAM Opposed Mode Sensor Pairs Leakproof 30-mm ac barrel sensors for demanding industrial applications Economical opposed mode sensor pairs in leakproof 30-mm threaded VALOX barrels quad-ring sealed acrylic lenses Ideal for high-humidity and high-pressure washdown applica- tions such as laundries, car washes, and food processing 20 to 250 volt ac operation 3-wire receiver hookup Receiver output is solid-state AC switch 300 milliamps maximum, continuous choice of light- or dark-operate models These are economical opposed mode sensor pairs in leakproof (NEMA 6P rated) 30- mm threaded barrel VALOX housings. Their size, shape, leakproof construction, 1/2 foot attached PVC-covered cable or a 4-pin mounting options, and price make them ideally suited for use in applications which micro-type quick disconnect (QD) connector. undergo high-pressure washdown, such as car washes and food processing. Mating QD cable must be ordered separately SM30 Series EZ-BEAM ac opposed mode pairs operate from 20 to 250V ac. The (see Specifications, below). receiver s solid-state output is capable of switching up to a 300-milliamp continuous Electronics are fully epoxy-encapsulated for load. Receivers are available with either light-operate or dark-operate output maximum resistance to mechanical shock and configuration. See Specifications section, below, for model listing. Any receiver vibration. Positive sealing at both ends of the may be paired with any emitter. Emitters and receivers must be ordered separately. sensor with no exposed epoxy interfaces elimi- Receivers have a red LED indicator that glows steadily whenever the receiversee nates all leakage paths (including capillary leak- the modulated light from the emitter and flashes to indicate marginal excess gain (1- age). The acrylic lens is quad-ring sealed. 1.5x) in the light condition. The LED is internally mounted to maintain the integrity The 30-mm threaded barrel housings of SM30 of the leakproof design, and is visible both through the front of the lens and through Series EZ-BEAM sensors enable them to be a sealed window on the side of the barrel near the lens. mounted in 30-mm clearance holes. A wide selection of mounting brackets is available. SM30 Series EZ-BEAM ac opposed mode sensor pairs are available with either a 6- Specifications and Model Listings Indicators: Sensing range: 60 meters (200 feet). Receivers have internally-mounted red LED that lights steadily whenever the receiversee the emitter s modulated light source, and flashes to indicate Sensing beam: Infrared, 880 nanometers. marginal excess gain (1-1.5x) in the light condition. LED is visible both through Supply voltage: 20 to 250V ac (50/60 Hz). the receiver s lens from the front and through a sealed window on the side of the Supply current: Average current 20 mA. barrel near the lens. Peak current 200 mA at 20V ac, 500 mA at 120V ac, 750 mA at 250V ac. Emitters have internally-mounted red LED that lights steadily to indicate AC POWER ON. LED is visible both through the emitter s lens from the front and Model listing and output configurations: through a sealed window on the side of the barrel near the lens. Use either emitter: SM303E (6-1/2 foot attached cable) or SM303EQ1 (micro-type QD fitting). Construction: Receivers solid-state ac output: M30x1.5 threaded VALOX tubular housing with positive sealing at both Model SM30AW3R = light-operate (6-1/2 foot attached cable) ends. Completely sealed epoxy-encapsulated circuitry. Quad-ring sealed Model SM30AW3RQ1 = light-operate (micro-type QD fitting) acryliclens. Exceeds NEMA 6P and IEC IP67 ratings. Two VALOX jam nuts Model SM30RW3R = dark-operate (6-1/2 foot attached cable) provided. Model SM30RW3RQ1 = dark-operate (micro-type QD fitting) Cabling: 6-1/2 foot long (2 meter) attached PVC-covered 2-wire cable Light operate models: Output conducts when the receiver sees the emitter s (emitters) and 3-wire cable (receivers), or 4-pin QD cable as follows: modulated light source. Dark operate models: Output conducts when sensing beam is blocked. MQAC-415 cable for models w/Q1 suffix 12 feet long, straight micro-type QD connector Output rating: 300 mA maximum (continuous). MQAC-415RA cable for models with Q1 suffix 12 feet long, Inrush capability 1 amp for 20 milliseconds, non-repetitive. right-angled micro-type QD connector Off-state leakage current <50 microamps. Vibration and mechanical shock: meets Mil. Std. 202F requirements. On-state voltage drop 3V at 300 mA ac 2V at 15 mA ac. Method 201A (Vibration: frequency 10 to 60 Hz, max., double amplitude 0.06- Response time: 16 millisecondso 8 millisecondsof independent of inch, maximum acceleration 10G). Method 213B conditions H & I (Shock: signal strength. No false pulse on power-up (false pulse protection circuit 75G with unit operating 100G for non-operation). causes a 100 millisecond delay on power-up). Operating temperature range: -40 to +70C (-40 to 158F). Repeatability 2 milliseconds independent of signal strength. Maximum relative humidity 90% at 50C (non-condensing). Printed in USA P/N 34428J4BHookup, SM30 Series EZ-BEAM ac opposed mode sensors (cabled models) Excess Gain Curve Receivers NOTE: Receivers SM30AW3R and SM30AW3RQ1 are light- operate. Output conducts when the receiver sees the emitter s modulated beam. Receivers SM30RW3R and SM30RW3RQ1 are dark- operate. Output conducts when the receiver does not see the emitter s modulated beam. Beam Pattern Emitters Any receiver may be paired with any emitter (SM303E or Hookup is SM303EQ1). without regard Hookup information for QD to wire color. sensors is provided with the sensor. Sensors with Q1 model suffix require QD (Quick Disconnect) cable. See Specifications section for information. Mounting Options for EZ-BEAM S30 Series Sensors Dimensions, EZ-BEAM SM30 Series sensors The model SMB30A right-angled mounting bracket (not shown) has a curved mounting slot for versatility and orientation. The SM30 Series sensor mounts to the bracket using a jam nut (supplied with the sensor). The curved mounting slot has clearance for 1/4- inch screws. Bracket material is 11-gauge stainless steel. The model SMB30S swivel-mount bracket (below, left) offers the ultimate in flexibility and convenience. This bracket mounts by its base. The SM30 threads into the adjustable captivebal of the bracket, which locks snugly in position when two clamping bolts are tightened. Bracket material is black VALOX . Hardware is stainless steel, and mounting bolts are included. The model SMB30C split clamp (not shown) mounts to a flat surface and grips the SM30 sensor by its threaded barrel. This bracket is similar to the SMB30S, but without the adjustable ball. Quick Disconnect fitting adds .35 (9 mm) in overall length to QD models. QD models require Quick Disconnect cable (order separately see Specifica- SM30 Series sensors may also be mounted in a 30-mm clear- tions section for information). ance hole, using the supplied jam nuts. SMB30S Swivel Mounting Bracket WARNING These photoelectric presence sensors do NOT include the self-checking redun- dant circuitry necessary to allow their use in person- nel safety applications. A sensor failure or malfunc- tion can result in either an energized or a de- energized sensor output condition. Never use these products as sensing devices for personnel protection. Their use as safety devices may create an unsafe condition which could lead to serious injury or death. Only MACHINE-GUARD and PERIMETER-GUARD Systems, and other systems so designated, are designed to meet OSHA and ANSI machine safety standards for point-of-operation guarding devices. No other Banner sensors or controls are designed to meet these standards, and they must NOT be used as sensing devices for personnel protection. WARRANTY: Banner Engineering Corporation warrants its products to be free from defects for one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. Banner Engineering Corp. 9714 10th Avenue No., Minneapolis, MN 55441 Telephone: (612) 544-3164 FAX (applications): (612) 544-3573