700 SERIES Industrial Wireless Radio 702-W THEINDUSTRIALNETWORKCOMPANY The N-TRON 702-W Industrial Wireless Radio provides outstanding performance and extreme reliability under the harshest industrial conditions. It is ideally suited for connecting wireless devices to a wired network or for connecting two wired networks where it is not possible, practical, or cost-effective to install cable. The 702-W provides three antennas to facilitate Multiple In, Multiple Out (MIMO) technology for increased throughput. Power over Ethernet (PoE) capability enables the unit to receive power through a Cat5e cable from a PoE sourcing device, such as N-Tron s 105TX-POE Switch or 100-PoE4 Midspan Injector. This ability makes deployments of network nodes much easier as a single Cat5e cable is all that is needed to carry both power and data. PRODUCT FEATURES One 10/100BaseTX RJ-45 port Three antennas for 3x3 MIMO operations Four user-de nable LEDs for display of signal quality Industrial Packaging and Speci cations Radio enable, link/activity, and power LEDs The 702-W is speci cally designed to operate in industrial environments. With its Station roaming rugged enclosure and industrial speci cationsincluding redundant power inputs 802.3af PoE-powered device and expanded tolerance to shock, vibration, electrical noise and temperature Extended environmental speci cations uctuationsthe 702-W easily meets and exceeds the operating parameters of connected equipment. Auto sensing 10/100BaseTX, duplex, and MDIX Rugged DIN-rail enclosure Multiple Wireless Modes The 702-W provides a number of con guration options that allow customization to Redundant power inputs (20-49 VDC) suit speci c applications. Web browser management Station: Instatio con guration, the 702-W is used to connect a single device Wireless Compliance (MAC Address) to a wireless access point. IEEE 802.11a Compliant Station, WDS (Wireless Distribution System): Instation, WD mode, IEEE 802.11b Compliant the 702-W can be connected to a remote wired switch, allowing multiple devices IEEE 802.11g Compliant (MAC Address forwarding) to be connected to the wireless access point when IEEE 802.11n Compliant WDS is activated. Security Access Point: Inaccess poin mode, the 702-W serves as a wireless switch for 802.11i with AES-CCM & TKIP Encryption attached wireless stations. Wireless access points are commonly used to create 802.1x, 64/128 bit WEP one wireless local area network (WLAN) that spans an area around the access point. Each access point typically supports up to 253 stations. Data Rates Legacy 802.11a/b/g (1-54 Mbps) Access Point, WDS (Wireless Distribution System): Inaccess point, WD 802.11n (up to 300 Mbps) mode, the 702-W provides wireless connections to a number of access points, expanding the coverage of the wireless network. In this con guration, the main Range Performance base access point is extended using a series of relay access points in WDS mode Indoor (antenna dependent) greater than 300m (Extended Service Set) and, in turn, can form a WLAN consisting of thousands Outdoor (antenna dependent) greater than 60km of stations. All stations should be con gured instation WD mode. Correctly APPLICATIONS con gured switches using WDS will create a single network, providing station The 702-W provides a reliable wireless connection that can be quickly and mobility throughout the wireless network. easily deployed at a fraction of the cost of hardwired installations. It is also ideal Multiple Network Modes for network communications between mobile devices such as forklifts, heavy Bridge: The 702-W will operate in Layer 2 without network segmentation. equipment, laptop computers, and other devices that are impractical or impossible to connect with copper or ber cable. Router: The 702-W offers Layer 3 routing to allow network segmentation. RUGGED RELIABLE AFFORDABLE www.n-tron.com702-W Scenario 1 Basic Bridge Access Point: Station: Theaccess poin mode allows the Instatio con guration, the 702-W is 702-W to serve as a wireless switch used to connect a single device (MAC for the wireless stations attached to it. address) to a wireless access point. Wireless access points are commonly used to create one wireless local area network (WLAN) that spans an area around the access point. Each access point typically supports up to 253 stations. For added security, the 702-W supports WEP, WPA , and WPA2 . WPA and WPA2, TKIP (Temporal Key Integrity Protocol) and CCMP (counter mode with Cipher Block Chaining Message Authentication Code Protocol) are available. Scenario 2 Control Network In station WDS mode, the 702-W can be connected to a remote wired Ethernet switch with multiple devices connected to the switch. www.n-tron.com