Streamer InTelematix J1708 and J1939 Heavy-duty Vehicle Interface Adapter Model HD3-A3 FEATURES Supports both J1939 (250k & 500k) & J1708 HDV interfaces Built to withstand harsh environments Wide temperature range (-40 to +85 C) Shock and vibration tested Over-the-air (OTA) upgradeable OVERVIEW ORDERING INFORMATION MODEL NUMBER DESCRIPTION B+B SmartWorx Model HD3-A3, heavy-duty vehicle interface adapter, connects HD3-A3 J1708 and J1939 Heavy Duty Vehicle Interface Adapter your onboard computer, wireless gateway, PC or laptop to the J1708/J1587 and J1939 bus found on most heavy-duty vehicles. The connection is made through a reliable, industry standard, wired, RS-232 interface. ACCESSORIES - sold separately Model HD3-A3 follows a simple operational protocol to communicate with the J1708 and J1939 bus, shielding the user from the complex vehicle D66Y Deutsch 6-Pin Y Cable interface. The HD3-A3 also solves timing problems often encountered when D99Y Deutsch 9-Pin Y Cable operating in Windows or other operating system environments. An embedded D99TYPE2 Deutsch 9-Pin Y Cable, 500k CAN microprocessor handles buffering and bus timing, reducing data collisions, allowing vehicle data access with much greater precision than a non-intelligent interface adapter. With the Streamer InTelematix database and algorithms, Model HD3-A3 provides a simple, operational protocol to communicate to the OBDII bus. The Command and Response Protocol Manual is available on B+B SmartWorx website. All product specifications are subject to change without notice. www.advantech-bb.com / Enabling an Intelligent Planet HD3-A3 4717dsStreamer InTelematix J1708 and J1939 Heavy-duty Vehicle Interface Adapter Model HD3-A3 SPECIFICATIONS Wide OperatingTemperature -40 to 85 C (-40 to 185 F) APPROVALS, DIRECTIVES, STANDARDS Input Voltage 10 to 42 VDC Radiated RF Interference SAE J1113/41 Input Current 12 VDC 50 mA typical, 134 mA maximum Load Dump and Transient Protection SAE J1113/11 104.1 x 43.2 x 20.3 mm ESD Immunity SAE J1113/13 Enclosure Dimensions (4.1 x 1.7 x 0.8 in) Environmental Testing Cable Dimensions 533 mm (21 in) integrated Y-cable Temperature Test - Ten (10) temperature cycles as follows with unit operating normally: Operating Voltage Range 8 to 30 VDC 1. Room (25 C) to Tmin in 15 minutes. MTBF (Meantime Before Failure) 174465 hours (19.9 years) 2. Soak at Tmin 1 hour with power removed from unit PORT CONNECTIONS 3. Start unit at Tmin, confirm successful start by executing a command/response. Power- RS-232 DB9 female, DCE down unit. Maintain unit un-powered for one minute between power-ups. Bus DB15 female 4. Repeat Step 3 three times. Pins 6,7 Ground 5. Start unit at Tmin and ramp Tmin to Tmax in 30 minutes Pin 8 Power 6. Operate at Tmax for 1 hour Pins 9, 10 CAN low, CAN high (500k) 7. Ramp Tmax to Tmin in 15 minutes Pin 12, 13 CAN low, CAN high (250k) 8. Repeat steps 1 through 7 nine times for a total of 10 cycles: Pins 14,15 J1708-, J1708+ a. 5 cycles at Vmin input b. 5 cycles at Vmax input Vibration Testing IEC 60068-2-6 10 sweeps of 10 to 500 to 10Hz at rate 0.5 oct/min. each axis Level to be 10 to 36Hz, 0.06 in DA 36 to 500Hz, 4gs Unit must remain operational during and after the test Shock Testing IEC 60068-2-27 18 to 50gs, 11ms, sine pulses, 3 each direction each axis Unit must remain operational during and after the test. Drop Testing IEC 60068-2-32 10 freefall drops from 1 meter onto concrete surface. Drop 1 time one each face (6), 1 on a corner and the 3 edges of this corner. The drop unit shall return to normal operation without physical damage. orders advantech-bb.com Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 support advantech-bb.com European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445