Advanced OBDII Data Streamer Models LDVDSV2-1587 & QCLDVSV2-KIT www.advantech-bb.com + Outputs OBDII data in J1708 data format + Ignition-On signal output + Status LEDs for vehicle connection and power + Automatic low power mode senses when vehicle speed and engine speed is zero + Automatic disconnect when technician scan tool is connected (requires separate OBDII Y-cable) + Proprietary vehicle detection algorithm and embedded database permits same hardware to work on all compliant vehicles + Wide Operating Temperature: -40 to 85 C (-40 to 185 F) + Low Power Consumption: 2W in Operating Mode 0.15W in Automatic Sleep Mode (Key Off) Model LDVDSV2-1587, OBDII Data Streamer, connects your PC, driver ORDERING INFORMATION terminal, Java-enabled phone, or other on-board computing device to the MODEL NO. DESCRIPTION OBDII diagnostic bus of light-duty and medium-duty vehicles. It enables the LDVDSV2-1587 OBDII Data Streamer/Converter retrieval of the most commonly used parameters of value in telematics and Bundled Kit, includes: fleet management applications. The OBDII Streamer supports any 1996 or QCLDVDSV2-KIT Model LDVSV2-1587 Streamer/Converter, Y cable, host newer vehicles that comply with the SAEs J1979 OBDII specification. cable, installation kit Model LDVDSV2-1587 provides a simple operational protocol to communicate to the OBDII bus. It provides a common interface and ACCESSORIES / REPLACEMENT PARTS deterministic response time for all vehicles. The complete Command and LDVYCBL - Y Cable Response Protocol is available on the company website. 45-JB723 - Host Cable Model QCLDVDSV2-KIT conveniently bundles the converter with 65-J9545-1 - Installation Kit, includes: 4 tie wraps, 1 alcohol wipe pad, 2 mounting tape strips accompanying cables and an installation kit. PROTOCOLS & PARAMETERS SUPPORTED PROTOCOLS SAE J1850 VPW SAE J1850 PWM SAE J2284/ISO 15765 (CAN) ISO 9141-2 ISO 14230-4 (KWP2000) SUPPORTED PARAMETERS Vehicle Identification Number Vehicle Speed - monitor aggressive driving Engine Speed - monitor idle time and engine abuse Throttle Position Odometer/Distance Traveled - monitor trip distance and HOS Instantaneous Fuel Rate in Gallons per Hour Total Fuel - Monitor MPG & protect against theft Ignition status track idle time Battery Voltage watch for charging system failures PTO Status - automatically figure fuel tax savings Diagnostic Trouble Codes MIL Status Emissions Readiness Monitors - check remotely if vehicles are ready for emissions certification Brake Switch Status and Seatbelt Fastened - available on most Ford & GM trucks and vans Other parameters available on a custom basis All product specifications are subject to change without notice. LDVDSV2 QCLDVSV2-KIT 0118ds orders advantech-bb.com Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 support advantech-bb.com European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445Advanced OBDII Data Streamer Models LDVDSV2-1587 & QCLDVSV2-KIT QCLDVDSV2-KIT SPECIFICATIONS LED STATE DESCRIPTIONS - On (LED ON): lit, solid - Off (LED OFF): unlit - FB (LED FAST): Alternating on-off 125ms on, 125ms off - SB (LED SLOW): Alternating on-off .5 sec on, 0.5 sec off - VSB (LED VERY SLOW): Alternating on-off 0.25 sec on, 2 sec off LEDS Red LED Green LED Red LED (Power) (Activity) (Debug) Actual State Description 1 On On Off Normal operation Normal operation 2 On SB Off Detecting vehicle Detecting vehicle 3 Off FB Off Database version mismatch Database needs to be updated 4 Off SB Off Update in progress Update in progress 5 Off VSB VSB Device asleep Device asleep 6 Off Off Off Device unpowered Device unpowered 7 Off On FB Error FPGA image invalid Firmware needs to be updated 8 Off Off FB Error with EMM code Update system manager 9 Off Off FB EMM checking CRC of images Wait 10 seconds. If state does not change, see 8. 10 Off SB FB Error writing/reading to/from flash during update. Restart update of current component. VEHICLE BUS CONNECTION - DB15 FEMALE APPROVALS, DIERECTIVES, STANDARDS Pin 1 ISO9141 K/ EMC TESTING Pins 4, 5 J1850-, J1850+ Radiated Interference SAE J1113/41 Pins 6, 7 Ground Load Dump and SAE J1113/11 Transient Protection Pin 9 Vehicle unswitched Vbat ESD Immunity SAE J113/13 Pin 10 ISO9141L ENVIRONMENTAL TESTING Pin 11 Vehicle Vbat to external scan tool Ten (10) temperature cycles as follows, with unit operating Pin 12 CAN Low normally: 1. Room (25C) to Tmin in 15 minutes. Pin 13 CAN High 2. Soak at Tmin 1 Hour with power removed from unit 3. Start unit at Tmin, confirm successful start by executing RS-232 CONNECTION - DB9 FEMALE (DCE) a command/response. Power-down unit. Maintain unit un- powered for one minute between power-ups. Optional Vbat Power In or Vbat Power Out Temperature Test Pin 1 4. Repeat Step 3 three times (2 separate build options) 5. Start unit at Tmin and ramp Tmin to Tmax in 30 minutes 6. Operate at Tmax for 1 hour Pin 3 J1708- 7. Ramp Tmax to Tmin in 15 minutes 8. Repeat steps 1 through 7 nine times for a total of 10 cycles: Pin 7 Ground a. 5 cycles at Vmin input Pin 8 J1708+ b. 5 cycles at Vmax input ADDITIONAL SPECIFICATIONS 10 sweeps of 10 to 500 to 10Hz at rate 0.5 oct/min. each axis. Vibration Test: Level to be 10 to 36Hz, 0.06 in DA 36 to 500Hz, 4gs IEC 60068-2-6 Dimensions 104.1 x 43.2 x 20.3 mm (4.1 x 1.7 x 0.8 in) Unit must remain operational during and after the test. Operating Shock Test: 18 to 50gs, 11ms, sine pulses, 3 each direction each axis 8 to 30 VDC Voltage Range IEC 60068-2-27 Unit must remain operational during and after the test. MTBF, 10 Freefall drops from 1 meter onto concrete surface. 111440 Hours Calculated Drop 1 time one each face (6), 1 on a corner and the 3 edges Drop Test: of this corner. IEC 60068-2-32 The drop unit shall return to normal operation without physical damage. orders advantech-bb.com Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 support advantech-bb.com European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445