EIR-x-Sx series-1012 - 1/2 Physical Description Hardened Compact Terminal Block and Power Inputs Media Converter Terminal Block Assignment PWR1 Power Input 1 (10 to 48VDC) GND Power Ground PWR2 Power Input 2 (10 to 48VDC) GND Power Ground Earth Ground 1. The relay opens if PWR1 or PWR2 fails 2. The relay opens if the Port Link is Down FAULT (When the Link Down Alarm is Enabled) While only one power source is required to power up the media converter, two power sources offer redundancy for those mission critical applications. (PWR1 and PWR2) The terminals labeled Fault are connected to a dry contact. The dry This quick installation guide describ d compact Media This quick installation guide describes how to install and contact is normally closed when either Converter. Capable of operating at temperature use the hardened compact Media Converter. Capable of power source is connected and active. extremes of -34 to +74C, this is the media converter operating at temperature extremes of -40 to +75C, this When no power is applied, the dry choice for harsh environments constrained by space. is the media converter of choice for harsh environments contact is normally open. constrained by space. LEDs and DIP Switch 10/100BaseTX and 100BaseFX Connectors LED Status: 10/100BaseTX Connections: LEDs State Indication Pin Regular Ports Uplink Port FAULT Steady Power or ports function abnormally 1 Receive Data + (input) Transmit Data + (output) Off Power and ports function normally 2 Receive Data (input) Transmit Data (output) PWR1 Steady Power on (PWR stands for POWER) 3 Transmit Data + (output) Receive Data + (input) PWR2 Off Power off 4 NC NC 10/100 Steady 100Mbps network connection 5 NC NC Off 10Mbps network connection 6 Transmit Data (output) Receive Data (input) LFP Steady LFPT function enabled 7 NC NC Off LFPT function disabled 8 NC NC LNK/ACT Steady Network connection established(LNK stands for LINK) Transmitting or receiving data(ACT stands for ACTIVITY) Flashing Off Neither a network connection established nor transmitting/receiving data FDX/COL Steady Connection in full duplex mode(FDX stands for FULL-DUPLEX) Flashing Collision occurred(COL stands for COLLISION) Off Connection in half-duplex mode DIP Switch Settings: Pos. Down(0) Up(1) 1 Disable Link-fault-pass-through Enable Link-fault-pass-through 100BaseFX Connections: 2 RJ45 Auto Negotiation Enabled RJ45 Forced Mode 3 RJ45 Forced to 100Mbps RJ45 Forced to 10Mbps The Tx (transmit) port 4 RJ45 Forced to Full Duplex RJ45 Forced to Half Duplex of device 1 is connected to the Rx 5 Fiber Forced to Full Duplex Fiber Forced to Half Duplex 6 Disable Link Down Alarm Enable Link Down Alarm (receive) port of device 2, and the Rx (receive) port of device 1 to the Tx (transmit) port of device 2. www.bb-elec.com orders bb-elec.com support bb-elec.com International Office: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 European Office: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 PRODUCT INFORMATION B&B ELECTRONICS EIR-x-Sx series-1012 - 2/2 Link-fault-pass-through Supports DIN-rail or Panel Mounting installation. Link-Fault-Pass-Through Overview UL1604 Class I, Division 2 Classified for use in hazardous When two Media Converters are connected via their locations (Applicable to versions with Terminal Block power fiber ports option). This equipment is suitable for use in Class I, Division 2, Link Fault of the FX port: Groups A, B, C and D OR non-hazardous locations only. A Link Fault condition will be sensed on the RJ45 port WARNING EXPLOSION HAZARD Do not disconnect whenever the media converter detects a Link Fault condition on the Fiber port. (The 10/100, LNK/ACT, and equipment unless power has been removed or the area is FDX/COL LED s will be off.) known to be non-hazardous. WARNING EXPLOSION HAZARD Substitution of Link Fault of the TX port: components may impair suitability for Class I, Division 2. The Media Converter A: A Link Fault condition will be sensed on the FX port whenever the media converter Assembly, Startup, and Dismantling detects a Link Fault condition on the TX port. Thus, the 100, LNK/ACT, and FDX/COL LEDs of the TX port of the Assembly: Place the media converter on the DIN rail from Media Converter A would be off. above using the slot. Push the front of the media converter toward the mounting surface until it audibly snaps into place. The Media Converter B: A Link Fault condition will be Startup: Connect the supply voltage to start up the media informed to the FX port of the Media Converter B. Then converter via the terminal block. a Link Fault condition will be sensed on the TX port of the Media Converter B whenever the Media Converter B Dismantling: Pull out the lower edge and then remove the detects a Link Fault condition on the FX port. Thus, the media switch from the DIN rail. 100, LNK/ACT, and FDX/COL LEDs of the Media Converter B would be off. Link Fault of the FX Port TX Port FX Port LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL Media Converter A ON OFF OFF OFF OFF OFF Media Converter B ON OFF OFF OFF OFF OFF Link Fault of the TX port of the Media Converter A TX Port FX Port LEDs PWR 100 LNK/ACT FDX/COL LNK/ACT FDX/COL Media Converter A ON OFF OFF OFF ON ON Media Converter B ON OFF OFF OFF OFF OFF Specifications Applicable Standards IEEE 802.3 10BaseT, IEEE 802.3u 100BaseTX & 100BaseFX Functional Description Fixed Ports (1) TX port, (1) FX port Speed 10BaseT 10/20Mbps for half/full-duplex Meets NEMA TS1/2 Environmental requirements 100BaseTX/FX 100/200Mbps for half/full-duplex such as temperature, shock, and vibration for traffic Switching Method Store-and-Forward control equipment. Forwarding rate 14,880/148,800pps for 10/100Mbps Meets IEC61000-6-2 EMC Generic Standard Cable 10BaseT 2-pair UTP/STP Cat. 3, 4, 5 up to 100m Immunity for industrial environment. 100BaseTX 2-pair UTP/STP Cat. 5 up to 100m 100BaseFX MMF (50 or 62.5m), SMF (9 or 10m) One channel media converter between LED Indicators Per Unit - PWR1, PWR2, FAULT, LFP 10/100BaseTx and 100BaseFx Per Port - TX: LNK/ACT, FDX/COL, 100 Support 802.3/802.3u/802.3x. Auto-negotiation: FX: LNK/ACT, FDX/COL 10/100Mbps, Full/half-duplex Auto MDI/MDIX. Dimensions 2 x 4.3 x 5.4 in. (5 x 11 x 13.6cm) Weight 0.6 Kg 100BaseFX: Multi mode SC or ST type Single mode Power Terminal Block: 200mA 24VDC, 10-48VDC SC type. Power Consumption 4.8W Max. DIP switch for configuring link-fault-pass-through, Operating Temperature -40C to 75C. Tested for functional operation at fixed speed, full/half duplex and link down alarm -40C to 85C. UL1604 Industrial Control Equipment certified Maximum Surrounding Air Store-and-forward mechanism Temperature 74C. Non-blocking full wire-speed forwarding rate Storage Temperature -45C to 93C Support broadcast storm filtering Humidity 10 to 95%, non-condensing Back-pressure & IEEE 802.x compliant flow control Safety Hazardous locations: Class I, Division 2 group A, B, C & D Alarms for power failure by relay output. UL 60950, EN60950, IEC60950 Emissions FCC Part 15, Class A Redundant 10-48 VDC terminal block power inputs. EN61000-6-3, EN61000-6-2 Supports DIN-rail mounting installation. Standards Front panel LED status. Field Wiring Terminal: Use Copper Conductors ESD Standard (EN61000-4-2) Radiated FRI Standards (EN61000-4-3) Only, 60/75 , 12-24 AWG torque value 7 lb-in. Burst Standards (EN61000-4-4) -40 to 75 (-40 to 167 ) operating Surge Standards (EN61000-4-5) Induced RFI Standards (EN61000-4-6) temperature range. Tested for functional operation Magnetic Field Standards (EN61000-4-8) -40 to 85 (-40 to 185 ). UL1604 Industrial Voltage Dips Standards (EN61000-4-11) Control Equipment certified Maximum Surrounding Environmental Test Compliance: Vibration Resistance (IEC 60068-2-6 Fc) Air Temperature 74 (165 ). Shock (IEC 60068-2-27 Ea) Free Fall (IEC 60068-2-32 Ed) NEMA TS1/2 Environmental requirements for traffic control equipment www.bb-elec.com orders bb-elec.com support bb-elec.com International Office: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 European Office: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 PRODUCT INFORMATION B&B ELECTRONICS