THEINDUSTRIALNETWORKCOMPANY The N-TRON 702M12-W Industrial Wireless Radio offers outstanding performance and ease of use. It is ideally suited for connecting wireless devices to a wired network or for connecting two wired networks in an IP67 environment, where it is not possible, impractical, or too expensive to install cable. Product Features Full IEEE 802.11a,b,g,n Compliance IP67 Rated, Industrial Hardened Enclosure One 10/100BaseTX M12 Port Three Antennas for 3x3 MIMO Operations Four user de nable LED s for display of signal quality Radio Enable, Link/Activity, and power LEDs 802.3af PoE Powered Device Extended Environmental Speci cations Autosensing 10/100BaseTX, Duplex, and MDIX Redundant Power Inputs (20-49 VDC) Industrial Packaging and Speci cations Web Browser Management The 702M12-W is speci cally designed to operate in industrial Wireless Compliance: environments. With it s rugged enclosure and industrial speci cations IEEE 802.11a/b/g/n Compliant such as extended shock and vibrations specs plus redundant power inputs, the 702M12-W easily meets and exceeds the operating Security: parameters of the connected equipment. 802.11i with AES-CCM & TKIP Encryption 802.1x, 64/128 bit WEP Multiple Wireless Modes The 702M12-W provides a number of con guration options that Data Rates: allow it to be customized to suit speci c application requirements. Legacy 802.11a/b/g (1-54Mbps), 802.11n (up to 300Mbps) Station: Instatio con guration the 702M12-W is used to connect a single device (MAC Address) to a wireless access point. Range Performance: Station, WDS (Wireless Distribution System): Instation, WD Indoor (Antenna Dependent) greater than 300m mode the 702M12-W can be connected to a remote wired switch Outdoor (Antenna Dependent) greater than 60km and will allow multiple devices (MAC Address forwarding) to be connected to the wireless access point with WDS activated. Applications In industrial environments, the installation of ber or Cat5e cable Access Point: TheAccess Poin mode allows the 702M12-W to serve as a wireless switch for the attached wireless stations. Wireless and associated power cables is dif cult or cost prohibitive. There access points are commonly used to create one wireless local area are also applications which require communication with mobile network (WLAN) that spans an area around the Access Point. Each devices such as laptop computers, forklifts, cockpits or control access point typically supports up to 253 stations. centers on mobile equipment such as cranes, and other devices which are impossible to connect with copper or ber cable. The Access Point, WDS (Wireless Distribution System): The N-TRON 702M12-W provides a wireless connection that can 702M12-W inAccess Point, WD mode allows wireless be quickly and easily deployed. With it s wide operating connection of a number of access points to extend the coverage of temperature range and 1 million hours MTBF, the 702M12-W the wireless network. The main base Access Point in WDS mode offers the industrial ruggedness that customers have come to is extended using a series of relay Access points in WDS mode expect of N-TRON products. The IP67 sealed enclosure insures (Extended Service Set) and can in turn form a WLAN consisting of that outdoor, wash down, and the most dusty environments will thousands of stations. All stations should be con gured inStation present no problems to the 702M12-W. Three antennas enable the WD mode. Correctly con gured switches using WDS will create use of Multiple-In, Multiple-Out (MIMO) technology for increased a single network, providing station mobility throughout the wireless network. throughput. Power over Ethernet (PoE) technology allows the 702M12-W to receive power through the Cat5e cable from a PoE Multiple Network Modes sourcing device, such as the N-TRON 105TX-POE Switch. This Bridge: In this mode the 702M12-W will operate in Layer two eliminates the need for power cables or power supplies for the without network segmentation. 702M12-W. Using wireless and PoE technology makes temporary Router: Router operating mode offers Layer three routing to allow deployment of network nodes much easier because only one Cat5e network segmentation. cable is required. THEINDUSTRIALNETWORKCOMPANY Scenario 1 Basic Bridge Access Point: Station: TheAccess Poin mode Instatio con guration allows the 702M12-W the 702M12-W is used to to serve as a wireless connect a single device switch for the wireless (MAC Address) to a stations attached to it. wireless access point. For added security, the 702M12-W supports WEP, WPA, and WPA2. WPA and WPA2, TKIP (Temporal Key Integrity Protocol) and CCMP (Counter Mode with Cipher Block Chaining Message Authentication Code Protocol) are available. Scenario 2 Control Network In Station WDS mode the 702M12-W can be connected to a remote wired Ethernet switch with multiple devices connected to the switch.