SMA 50 Ohm INCHES (MILLIMETERS) Right Angle Crimp Type Plug - CUSTOMER DRAWINGS AVAILABLE UPON REQUEST Captivated Contact Low Loss Cable B CABLE TYPE VSWR & FREQ. RANGE GOLD PLATED NICKEL PLATED A LMR-200, HPF-200, RF-200 1.10 + .06f (GHz) 0-12.4 GHz 142-0439-101 142-0439-106 .611 (15.52) .470 (11.94) CABLE GROUP PART NUMBER CRIMP HEX 142-4439-101 .213 (5.41) LMR-200 142-4439-106 .213 (5.41) 1. Identify connector parts. (3 piece parts) 2. Strip cable to dimensions shown. Do not nick braid, foil or center con- ductor. Cut foil flush with dielectric, do not remove foil. Make sure that dielectric is clean and free from all particles. Tin center conductor, keeping solder amount to a minimum. Slide crimp sleeve onto jacket of cable. 3. Flare braid and slide body assembly over foil and dielectric, then un- der braid. Make sure cable center conductor is contained within con- nector contact, but do not allow foil and dielectric to enter body access port. Solder center conductor to contact through the rear access port. Use a minimum amount of solder for a full fillet joint020 (0.51) Diam- eter solder is recommended. 4. Arrange braid uniformly around crimp stem. Slide crimp sleeve for- TM ward and crimp using Johnson Components hand crimp tool 141- 0000-913 and recommended crimp die hex. Place expansion cap in access port and seat with recommended Diameter flat punch. Low Loss Dia. A Crimp Die Hex Flat Punch Dia. 0.200 .110 (2.79) .213 (5.41) hex .187 (4.75) CCinincch Ch Coonnnnecectitivitvity Soy Solulutitioonsns 299 J299 Johnsohnson Aon Avveennue Sue SWW, W, Waassecaeca, MN 56093 U, MN 56093 USSA 800.247.8256 +1 507 833 8822 cA 800.247.8256 +1 507 833 8822 cincinchchconneconnectitivitvityy.c.com om SMA - 50 Ohm Connectors Specifications INCHES (MILLIMETERS) CUSTOMER DRAWINGS AVAILABLE UPON REQUEST ELECTRICAL RATINGS Insertion Loss: (dB maximum) Impedance: 50 ohms Straight flexible cable connectors Frequency Range: and adapters ...................... 0.06 f (GHz), tested at 6 GHz Dummy loads .......................................................................... 0-2 GHz Right angle flexible cable Flexible cable connectors ................................................... 0-12.4 GHz connectors ......................... 0.15 f (GHz), tested at 6 GHz Uncabled receptacles, RA semi-rigid and adapters ........... 0-18.0 GHz Straight semi-rigid cable Straight semi-rigid cable connectors and connectors with contact ..... 0.03 f (GHz), tested at 10 GHz field replaceable connectors ............................................... 0-26.5 GHz Right angle semi-rigid cable VSWR: (f = GHz) Straight Right Angle connectors ......................... 0.05 f (GHz), tested at 10 GHz Cabled Connectors Cabled Connectors Straight semi-rigid cable RG-178 cable .............................. 1.20 + .025f 1.20 + .03f connectors w/o contact ...... 0.03 f (GHz), tested at 16 GHz RG-316, LMR-100 cable .............. 1.15 + .02f 1.15 + .03f Straight low loss flexible RG-58, LMR-195 cable ................ 1.15 + .01f 1.15 + .02f cable connectors ................ 0.06 f (GHz), tested at 1 GHz RG-142 cable ............................... 1.15 + .01f 1.15 + .02f Right Angle low loss flexible LMR-200, LMR-240 cable ............ 1.10 + .03f 1.10 + .06f cable connectors ................ 0.15 f (GHz), tested at 1 GHz .086 semi-rigid ............................ 1.07 + .008f 1.18 + .015f Uncabled receptacles, field replaceable, dummy loads .....................N/A .141 semi-rigid (w/contact) .......... 1.05 + .008f 1.15 + .015f Insulation Resistance: 5000 megohms minimum .141 semi-rigid (w/o contact) ...... 1.035 + .005f Contact Resistance: (milliohms maximum) Initial After Environmental Jack-bulkhead jack adapter and plug-plug adapter ................. 1.05 + .01f Center contact (straight cabled connectors Jack-jack adapter and plug-jack adapter ............................... 1.05 + .005f and uncabled receptacles) ........................... 3.0* 4.0* Uncabled receptacles, dummy loads .................................................. N/A Center contact (right angle cabled Field replaceable (see page 59) ......................................................... N/A connectors and adapters) ..............................4.0 6.0 Working Voltage: (Vrms maximum) Field replaceable connectors ........................6.0 8.0 Connectors for Cable Type Sea Level 70K Feet Outer contact (all connectors) ...........................2.0 N/A RG-178 ...................................................................... 170 45 Braid to body (gold plated connectors) .............0.5 N/A RG-316 LMR-100, 195, 200 ..................................... 250 65 Braid to body (nickel plated connectors) ...........5.0 N/A RG-58, RG-142, LMR-240, .086 semi-rigid, *N/A where the cable center conductor is used as a contact uncabled receptacles, .141 semi-rigid w/o contact ... 335 85 RF Leakage: (dB minimum, tested at 2.5 GHz) .141 semi-rigid with contact and adapters ................. 500 125 Flexible cable connectors, adapters and .141 semi-rigid Dummy loads ................................................................................. N/A connectors w/o contact ............................................................. -60 dB Dielectric Withstanding Voltage: (VRMS minimum at sea level) Field replaceable w/o EMI gasket .............................................. -70 dB Connectors for RG-178 ................................................................... 500 .086 semi-rigid connectors and .141 semi-rigid connectors Connectors for RG-316 LMR-100, 195, 200 .................................. 750 with contact, and field replaceable with EMI Gasket ................ -90 dB Connectors for RG-58, RG-142, LMR-240, .086 semi-rigid, Two-way adapters ...................................................................... -90 dB field replaceable, uncabled receptacles ...................................... 1000 Uncabled receptacles, dummy loads .............................................. N/A Connectors for .141 semi-rigid with contact and adapters ............ 1500 RF High Potential Withstanding Voltage: (Vrms minimum, tested at 4 Connectors for .141 semi-rigid w/o contact, dummy loads .............. N/A and 7 MHz) Corona Level: (Volts minimum at 70,000 feet) Connectors for RG-178 ................................................................... 335 Connectors for RG-178 ................................................................... 125 Connectors for RG-316 LMR-100, 195, 200 .................................. 500 Connectors for RG-316 LMR-100, 195, 200 .................................. 190 Connectors for RG-58, RG-142, LMR-240, .086 semi-rigid, Connectors for RG-58, RG-142, LMR-240, 086 semi-rigid, .141 semi-rigid cable w/o contact, uncabled receptacles .............. 670 uncabled receptacles, .141 semi-rigid w/o contact .......................... 250 Connectors for .141 semi-rigid with contact and adapters ............ 1000 Connectors for .141 semi-rigid with contact and adapters .............. 375 Power Rating (Dummy Load): 0.5 watt + 25C, derated to 0.25 watt Dummy loads ...................................................................................... N/A +125C MECHANICAL RATINGS Engagement Design: MIL-C-39012, Series SMA Cable Retention: Axial Force*(lbs) Torque (in-oz) Engagement/Disengagement Force: 2 inch-pounds maximum Connectors for RG-178 ............................ 10 N/A Mating Torque: 7 to 10 inch-pounds Connectors for RG-316, LMR-100 ........... 20 N/A Bulkhead Mounting Nut Torque: 15 inch-pounds Connectors for LMR-195, 200 .................. 30 N/A Coupling Proof Torque: 15 inch-pounds minimum Connectors for RG-58, LMR-240 ............. 40 N/A Coupling Nut Retention: 60 pounds minimum Connectors for RG-142 ............................ 45 N/A Contact Retention: Connectors for .086 semi-rigid ................. 30 16 6 lbs. minimum axial force (captivated contacts) Connectors for .141 semi-rigid ................. 60 55 4 inch-ounce minimum torque (uncabled receptacles) *Or cable breaking strength whichever is less. Durability: 500 cycles minimum 100 cycles minimum for .141 semi-rigid connectors w/o contact ENVIRONMENTAL RATINGS (Meets or exceed the applicable paragraph of MIL-C-39012) Temperature Range: - 65C to + 165C Shock: MIL-STD-202, Method 213, Condition I Thermal Shock: MIL-STD-202, Method 107, Condition B Vibration: MIL-STD-202, Method 204, Condition D Corrosion: MIL-STD-202, Method 101, Condition B Moisture Resistance: MIL-STD-202, Method 106 Avoid user injury due to misapplication. See safety advisory definitions inside front cover. CCinincch Ch Coonnnnecectitivitvity Soy Solulutitioonsns 299 J299 Johnsohnson Aon Avveennue Sue SWW, W, Waassecaeca, MN 56093 U, MN 56093 USSA 800.247.8256 +1 507 833 8822 cA 800.247.8256 +1 507 833 8822 cincinchchconneconnectitivitvityy.c.com om