5 4 3 2 1 DRAWING NO. ITEM 1 ITEM 2 ITEM 3 ITEM 4 ITEM 5 COUPLING NUT PART NUMBER BODY CONTACT INSULATOR CRIMP SLEEVE 27-9213 CONTROLLED DOCUMENT BRASS DELRIN ZINC 27-9213 BRASS BRASS REVISIONS NICKEL PLATED WHITE NICKEL PLATED GOLD PLATED NICKEL PLATED RELEASE FOR QUTATION Mar 24,08 27-9230 0B P/N Rev Rel d Date A Z W T 11-09-07 REVISE INSULATOR PP TO DELRIN 25 B Z W T Thomas 01-25-08 Chow D REF 14.9 D 17 u0.3 REF 9.7 5 3 2 O 6.5 O 5.60 O 8.40 O 9.0 O 7.7 4 1 REF O14.5 17.20 0.3 17 u0.3 C C REF 9.7 REF 9.7 O 7.2 O 6.40 O 8.40 O 9.0 O 8.1 O 7.50 O 8.40 O 9.0 4 4 NOTES: B B 1. ELECTRICAL SPECIFICATIONS IMPEDANCE: 50 OHMS NOMINAL FREQUENCY RANGE: 0-4 GHz WORKING VOLTAGE: 500 Vrms MAX AT SEA LEVEL DIELECTRIC WITHSTANDING VOLTAGE: 1500 vrms AT SEA LEVEL CORONA LEVEL:375 VOLTS MINIMUM AT 70,000 FEET CONTACT RESISTANCE:OUTER - NICKEL PLATED INITAL 2.5 MILLIOHMS MAXIMUM 9.5 AFTER ENVIRONMENTAL 3.5 MILLIOHMS MAXIMUM CENTER - INITIAL 3 MILLIOHMS MAXIMUM AFTER ENVIRONMENTAL 4 MILLIOHMS MAXIMUM BRAID TO BODY - 2.5 MILLIOHMS MAXIMUM (NICKEL PLATED), AFTER ENVIRONMENTAL NOT APPLICABLE INSULATION RESISTANCE: 5000 MEGOHMS MINIMUM CABLE STRIP DIMENSIONS ASSEMBLY INSTRUCTIONS ON SHEET 2 2. MECHANICAL SPECIFICATIONS DURABILITY: 500 CYCLES MIN CABLE ACCEPTABILITY: RG6,RG58,RG59,RG59 PLENUM THIS DRAWING TO BE INTERPRETED CABLE RETENTION:20 lbs MIN PER ANSI Y 14.5M - 1994 THE MATERIAL OF CRIMP SLEEVE SHALL HAVE A MAXIMUM HARDNESS OF 85 VICKERS. COMPANY CONFIDENTIAL 3. ENVIRONMENTAL SPECIFICATIONS A A DRAWN BY DATE RECOMMENDED TEMPERATURE RANGE: -55 TO +85 TOLERANCE UNLESS Connectivity OTHERWISE SPECIFIED GARY.ZHG 01-25-08 MOISTURE RESISTANCE: MIL-STD-202 DECIMALS mm CHECKED BY DATE Solutions 4. PRODUCT SHOULD BE RoHS COMPLIANCE. X + LINDA.WU 01-25-08 - 0.5 TITLE APPROVED BY 50 OHM BNC(M) CRIMP-ON, X.X + 0.2 DATE - 5. PACKAGING REQUIREMENT FOLLOWS ENGINEER DOCUMENT P/N 836-40200001XX 2 PIECE, (3) FERRULES FOR X.XX 01-31-08 + 0.1 THOMAS - RG-6, 58, 59 & 59TFE ANGLES + 0.5v U/M mm - SHEET DRAWING NO. SIZE THIS DRAWING WAS PRODUCED BY COMPUTER, 1 OF 2 C DO NOT SCALE DRAWING OR UPDATE MANUALLY. 27-9213 543 21 5 4 3 2 1 DRAWING NO. CRIMP CRIMP RECOMMENDED CABLE BRAID HEX (STRAIN RELIEF) CRIMP TOOL PART NUMBER 27-9213 CONTROLLED DOCUMENT 27-9213 RG6,RG58,RG59 8.13 5.41/6.48 24-8859P REVISIONS RG59 TFE RELEASE FOR QUTATION Mar 24,08 27-9230 0B P/N Rev Rel d Date A Z W T 11-09-07 VERSION UPDATE B Z W T CRIMP SLEEVE 01-25-08 D D CONNECTOR BODY JACKET CRIMP SLEEVE 9.5 BRAID C C BRAID FOLDED BACK 7.92 CENTER CONDUCTOR INSULATOR ASSEMBLY INSTRUCTIONS 1. RUN CRIMP SLEEVE DOWN CABLE. 2. TRIM CABLES AS SHOWN,TAKING CARE NOT TO NICK OUTER BRAID. 3. INSERT CENTER CONDUCTOR INTO THE GUIDE HOLE IN THE REAR OF THE CONNECTOR. THEN SCREW THE CONNECTOR ON THE CABLE IN A CLOCKWISE DIRECTION. B B 4. PUSH CRIMP SLEEVE INTO PLACE, SANDWICHING THE BRAID BETWEEN THE CONNECTOR AND SLEEVE. 5. CRIMP THE SLEEVE INTO PLACE WITH THE PROPER CRIMP TOOL. (BRAID HEX) ( STRAIN RELIEF ) THIS DRAWING TO BE INTERPRETED PER ANSI Y 14.5M - 1994 COMPANY CONFIDENTIAL A CRIMP A DRAWN BY DATE TOLERANCE UNLESS Connectivity OTHERWISE SPECIFIED GARY.ZHG 01-25-08 DECIMALS mm CHECKED BY DATE Solutions X + LINDA.WU 01-25-08 - 0.5 TITLE APPROVED BY 50 OHM BNC(M) CRIMP-ON, X.X + 0.2 DATE - 2 PIECE, (3) FERRULES FOR X.XX 01-31-08 + 0.1 THOMAS - RG-6, 58, 59 & 59TFE ANGLES + 0.5v U/M mm - SHEET DRAWING NO. SIZE THIS DRAWING WAS PRODUCED BY COMPUTER, 1 OF 2 C DO NOT SCALE DRAWING OR UPDATE MANUALLY. 27-9213 543 21