SFP-1GBT-06 Bel Fuse

SFP-1GBT-06 SFP Copper Transceiver 1000Base-T to GBIC The Bel SFP-1GBT-06 transceiver is an internally configured 1000Base-T SFP module for GBIC host interface. The host interface transmits and receives serial data differentially at 1.25 Gbps. The copper interface is advertised as full duplex and will auto- negotiate to 10/100/1000 Base-T. Key Features & Benefits Designed with Broadcoms BCM54616S chipset Complies with IEEE 802.3, 802.3u, and 802.3ab specifications Conforms to Multi-Source Agreement (MSA) specifications for SFP transceivers Supports IEEE 802.3u and IEEE 802.3ab autonegotiation features to allow networking equipment to automatically determine and adjust the required settings Operates in extended temperature range of -40 to +85 C Automatically compensates for baseline wander by removing DC offset from the input signal Assembled with low EMI emissions IC and fully metallic housings Automatic dependent interface (DI) crossover, eliminating the need for crossover cables or cross-wire (MDIX) ports Bail latch provides ease of extraction Compact RJ45 connector assembly Data is scrambled to reduce radiated emission Power consumption is 610mW typical Fully RoHS compliant 2 The BCM54616S physical layer IC (PHY) can be accessed via I C interface: PHY address = ACh EEPROM address = A0h Applications 1000 Mbps data rate in excess of 100 meters of Category 5/5e cable Industrial temperature environments -40 to +85 C Networking equipment Switch-to-switch interface Routers Regulatory and Standards Compliance Compliant with IEEE 802.3:2000 FCC Part 15, Class A EN55022 Class A CE E55024 Immunity standard and ESD Bel Modules +44 1622 757 395 28 Turkey Court, Turkey Mill, Ashford Road techhelp belf.com Maidstone Bel ME 14 5PP UK belfuse.com 2017 Bel Power Solutions, Inc. SFP-1GBT-06 v4 12.15 SFP-1GBT-06 SFP Copper Transceiver 1000Base-T to GBIC SFP-1GBT-06 Module Specifications Parameter Symbol Min Type Max Units Notes Supply Voltage V 3.13 3.3 3.46 V DD3 Supply Current Is 185 mA 1000 Base-T SFP Host Serial Interface Symbol Min Type Max Units Notes (TX/RX) Line Frequency FLINE 125 MHz TX Output Impedance ZTX OUT 100 Differential RX Output Impedance ZRX IN 100 Differential Clock Frequency 25 MHz Rise/Fall Time T /T 4 Ns 20% - 80% R F RMS Phase Jitter F 1.5 ps-rms FJ = 12 KHz to 20 MHz offset frequency J Environmental Specifications Symbol Min Type Max Units Notes Operating Temp T -40 +85 C Case temperature OP Storage Temp TSTG -40 +85 C Ambient temperature SFP Host Connector Electrical Interface Descriptions Pin Name Descriptions 1 VeeT Transmitter ground (common with receiver ground) 2 TX Fault Transmitter fault is internally tied to transmit ground and is not supported 3 TX Disable Disable PHY when logic 1 . Internal Pull Down 4 MOD-DEF2 Signal SDA (data) of the two-wire serial interface 5 MOD-DEF1 Signal SCL (clock) of the two-wire serial interface 6 MOD-DEF0 This pin is internally tied to transmit ground 7 Rate Select Not implemented. This Pin is floating internally 8 LOS Logic 1 when no signal or linked at 10Base-T 9 VeeR Receiver ground (common with transmitter ground) 10 VeeR Receiver ground (common with transmitter ground) 11 VeeR Receiver ground (common with transmitter ground) 12 RD- Differential Transmitter Output. User to terminate 100 differential at host. AC Coupled within SFP. 13 RD+ Differential Transmitter Output. User to terminate 100 differential at host. AC Coupled within SFP. 14 VeeR Receiver ground (common with transmitter ground) 15 VccR 3.3V power 16 VccT 3.3V power 17 VeeT Transmitter ground (common with receiver ground) 18 TD+ Differential Receiver Input. 100 differential termination & AC Coupling within SFP. 19 TD- Differential Receiver Input. 100 differential termination & AC Coupling within SFP. 20 VeeT Transmitter ground (common with receiver ground) techhelp belf.com belfuse.com