1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 S200 3 sec 3 sec 2 2 10 10 2012 STANLEY TOOLS www.STANLEYTOOLS.com 701 East Joppa Road STHT77406 REV A 06/12 Towson, Maryland 21286 10 10 10 10 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 3 sec3 sec3 sec3 sec 2 2 2 2 10 10 10 10Stanley Stud Sensor 200 relative position of the stud on the screen. Conventional Construction SPECIFICATIONS 6 When it detects the stud center, the Doors and windows are commonly constructed The Stud Sensor 200 uses electronic signals (At 35-55% relative humidity) Center icon will appear on the LCD and with additional studs and headers for added to locate the center of studs, joists or live AC Battery 9 volt (not included) an audible tone will sound. Use the marking stability. The Stud Sensor 200 detects the edge wires through drywall or other common building Depth Range channel located at the top of the unit to mark of these double studs and solid headers as a materials. Once the center of a stud has been detected in one pass across the surface, the Stud the stud center. single, wide stud. Wood or Metal Studs Up to (19 mm) through drywall Detecting Live AC Wires Surface Differences Sensor 200 gives a visual display and sounds an Live AC Wires (120 volts AC) Up to 2 (50 mm) through drywall 10 The live wire red LED will illuminate, the The Stud Sensor 200 will scan through common audible tone. A marking channel allows you to Accuracy - Stud Center AC icon will appear on the LCD, and the building materials, Including: easily note the stud center and edges on the Stud Sensor 200 sounds an audible tone, Gypsum drywall wall. Wood 1/8 (3 mm) warning when in the proximity (typically Plywood sheathing Metal 1/4 (6 mm) within 4 to 18 along the surface) from a live Hardwood floors Note: Read all instructions prior to operating the Operating Temperature +32F to +120F (-0C to +49C) wire. Linoleum over wood Stud Sensor 200 and DO NOT remove any labels Wallpaper from the tool. Surface Temperature -4F to +150F (-20C to +66C) Note: Static electrical charges that can The scanner cannot scan through: develop on drywall and other surfaces will Carpeting OPERATING INSTRUCTIONS WARRANTY spread the voltage detection area many Foil faced materials Battery Stanley Tools warrants the Stud Sensor 200 1 inches on each side of the actual electrical Ceramic tile Open door on back of unit and connect a against defects in material and workmanship wire. To aid in locating the wire position, Cement or concrete 9 volt battery (not included) to clip. Put battery for one year from the date of purchase. Stanleys scan holding the unit away from the Metal & plaster walls back into case and close back battery door. liability under this warranty is limited the wall surface or place your other hand on the Wallpaper replacement of the unit. Any attempt to repair surface approximately 12 from sensor. There will be no difference in the function of Note: Recommend to replace a new 9 volt the product by other than factory authorized the Stud Sensor 200 on surfaces covered with battery when low battery - Low Battery will personnel will void this warranty. Calibration, Warning: Shielded wires or wires in metal wallpaper or fabric unless the coverings used appear on the LCD. batteries and maintenance are the responsibility conduits, casings, metallized walls or thick, contain metallic foil or fibers. of the user. Where permitted by law, Stanley is dense walls will not be detected. Always turn Ceilings Usage not responsible for incidental or consequential off AC power when working near wiring. When dealing with a rough surface such as Detecting Wood / Metal Studs damages. Agents of Stanley cannot change 2 a sprayed ceiling, utilize a piece of cardboard Hold the Stud Sensor 200 flat against the this warranty. Stanley is not responsible for 3 Cautions on Operating when scanning the surface. Run through the surface, making firm contact. Press in and damage resulting from wear, abuse or alteration You should always use caution when nailing, calibration technique described earlier with hold the activation button. A series of tones of this product. The user is expected to follow 4 cutting and drilling in walls, ceilings and the piece of cardboard too, to assure best will sound. When the unit is calibrated ALL operating instructions. This warranty may floor that may contain wiring and pipes near performance of the unit. Also, it is particularly the Ready icon will appear on the LCD. provide you with additional rights that vary by 5 the surface. Always remember that studs important in this application to remember to Keep holding the activation button during state, province or nation. or joists are normally spaced 16 inches or keep your free hand away from the unit. all of the following procedures. 24 inches apart and are 1 inches in width. To WARNING: 3 avoid surprises, be aware that anything closer Note: The thickness, density and moisture Note: The unit cannot be moved before Protect Your Eyes, Wear Safety Goggles. 2 together or of a different width may not be a content of the surface material will affect the calibration is complete. While calibrating, stud. sensing depth. the Stud Sensor 200 must not be placed directly over a stud, dense material such as OPERATING TIPS IMPORTANT SAFETY NOTICE metal, or over a wet or newly painted area, 11 The Stud Sensor 200 is designed for use only on Insure proper detection of live wires. Always or it will not properly calibrate. If all segments of the LCD flash on and off when interior surfaces. hold the Stud Sensor 200 in the handle area only. Prevent Interference Grasp between fingers and thumb while making the activation button is pressed, move the To ensure best performance from the Stud contact with your palm. Stud Sensor 200 to a different location and Sensor 200, keep your free hand at least try again. Releasing the activation button will 6 inches away from the unit and wall surface turn off the sensor. while testing or scanning surfaces. 6 Slide the Stud Sensor 200 slowly across 2012 STANLEY TOOLS 9 www.STANLEYTOOLS.com the surface in a straight line. As it detects 701 East Joppa Road a stud, the Stud Sensor 200 will display the Towson, Maryland 21286