PM-0748-400-0 Block

Electronic circuit breaker with thermomagnetic characteristic PM-0748-400-0 Advantages Adjustable tripping current for each output channel via current selector switch accessible from the front Ability to turn-on high load capacitance at each channel Sequential and load-dependent switching-on of channels Comprehensive single-channel-diagnostics and remote switching on/off of each output channel via 2-wire-interface LED signalization and remote request for each output channel Group alarm contact for simple diagnosis Applications ECONOMY SMART circuit breakers with a thermomagnetic characteristic represent an economical alternative to the classic circuit breaker. They also ensure reliable tripping even in the case of high line resistance. This makes the circuit breakers ideal for use in standard machine production. The electronic circuit breaker distributes and monitors the load current over several current circuits. Overloads and short circuits on an output are reliably recognized. The electronics permit brief current peaks and switch longer overloads off. The rated current for each output can be individually set with a current selector switch accessible from the front. The outputs are activated depending on the time delay and load to avoid an overload current. If the rated current is exceeded for a certain amount of time, the output will be switched off automatically and can be reactivated after a waiting time (thermal relaxation) using the pushbutton or the remote signal input S1. The pushbutton can also be used to switch the output manually. It is possible to read out the state of each output using the three signal contacts. The state of each output is also indicated with a multi-colored LED. Picture shows PC-0724-800-0, PM-0724-400-0 Approvals U o Z Standards Z Safety: UL 2367, UL 508, GL EN 60950-1, EN 50178, EN/IEC 60204-1 EMC: EN 61000-6-2, EN 61000-6-3 Safety extra-low voltage (SELV/PELV): IEC 60364-4-41 (DIN VDE 0100-410) CE acc. to 2004/108/EG (EMC-Directive) Electronic circuit breaker with thermomagnetic characteristic PM-0748-400-0 Type PM-0748-400-0 Type PM-0748-400-0 Input Input Input rated voltage 48 Vdc Input terminals (2 x), 1) direct plug-in technology 1) max. 2,5 mm Push-in 2) pluggable, WAGO series 721 32 - 58 Vdc Input voltage range Input terminals (2 x), 1) direct plug-in Maximal residual ripple of supplied input voltage 3 % 1) max. 6 mm technology Push-in 2) pluggable, WAGO series 831 Required input voltage for turning-on of outputs 35 Vdc Output 40 A Max. total input current Output terminals ), 1) direct plug-in technology Max. input current for each pole of terminal 40 A 1) max. 2,5 mm Push-in 2) pluggable, WAGO series 721 Suppressor diode 68 V Over voltage protection Signaling Stand-by current 17 mA Power losses in stand-by mode 0.82 W Connections signalling, 1) direct plug-in technology 1) max. 2,5 mm Push-In 2) pluggable, WAGO series 721 Output Terminal and mounting Output rated voltage 48 Vdc Mounting position horizontal for standard rail DIN TH 35 4x (2, 3, 4, 6, 8, 10 A) adjustable Output rated current 175 mV (4 x 10 A) Maximum voltage drop between input and output Measures and weights Initialization time of module 250 ms Weight 0.14 kg Load dependent, min. 50 ms / max. 5 s Turn-on delay of outputs Waiting periode after switch-off of an output 500 ms (short circuit) ... 20 s (overload) 99 % Efficiency 8 W (4 x 10 A) Max. power losses 3.5 Internal output fuse 15 A 58 Vdc Resistance to reverse feed max. Parallel use of outputs Not allowed 90.0 Not allowed Serial use of outputs Signaling Status indicator LED (red, green, orange) 45.0 15 - 58 Vdc (On / Off / Reset) Signal input S1S2: 24 Vdc, 20 mA, short circuit proof, status Signal output S2 report of outputs 3.0S3: 24 Vdc, 20 mA, short circuit proof high = 45.0 Signal output S3 OK, low = min. one channel tripped Approvals - Approvals Environment -25 C ... +85 C Storage temperature Ambient temperature -25 C ... +70 C Derating - Natural convection Cooling method Required minimum spacing (left/right) 0 mm 40 mm Required minimum spacing (over/under) Safety and protection Protection index IP 20 III, without PE connection Safety class Degree of pollution 2 Order numbers PM-0748-400-0 Order Number 99.0 91.5 - + 30 Subjects to change.