CR1206-FX-15R4ELF Bourns

01R Features n Three layer contacting process with n RoHS compliant* nickel barrier prevents leaching and n Power rating at 70 C: CR0603 - 0.10 W, provides excellent solderability CR0805 - 0.125 W, CR1206 - 0.25 W n Paper tape on reel for automatic n Tight tolerances of bottom electrode placement width n Suitable for all types of soldering processes CR0603/CR0805/CR1206 - Chip Resistors Electrical Characteristics Characteristic Model CR0603 Model CR0805 Model CR1206 Power Rating 70 C 1/10 W 1/8 W 1/4 W Operating Temperature Range -55 C to +155 C Derated to 0 Load at +155 C Maximum Working Voltage 50 V 150 V 200 V Maximum Overload Voltage 100 V 300 V 400 V 10 ohms R 1M ohms 100 PPM/C Resistance Range: 1 % E-96 + E-24 1M ohms < R 10M ohms 200 PPM/C 10 ohms R 10M ohms 200 PPM/C Resistance Range: 5 % 1 ohm R < 10 ohms E-24 10M ohms < R 20M ohms 400 PPM/C Zero Ohm Jumper <0.05 ohm 1 A / 2.5 A 2 A / 5 A 2 A / 5 A Rated / Maximum Current AEC-Q200: Contact Bourns to confirm availiability. For Standard Values Used in Capacitors, Inductors, and Resistors, click here. Dimensional Drawings Chip Dimensions Characteristic Data Model Model Model I I 1 1 Dimension CR0603 CR0805 CR1206 1.600.10 2.000.15 3.200.25 H L (0.0630.004) (0.0790.006) (0.1260.010) 0.800.10 1.250.15 1.600.15 W (0.0310.004) (0.0490.006) (0.0630.006) I I 2 2 0.450.10 0.500.10 0.600.15 W H (0.0180.004) (0.0200.004) (0.0240.006) L 0.300.20 0.400.20 0.500.25 Resistor (Ru02) Overcoat I1 (Jumper chip is (0.0120.008) (0.0160.008) (0.0200.010) a conductor) 0.300.20 0.400.20 0.500.20 I2 (0.0120.008) (0.0160.008) (0.0200.010) MM DIMENSIONS: (INCHES) Derating Curve Alumina Substrate Internal Electrode (Ag) Secondary Electrode (Nickel Plated) 100 External Electrode (tin-plated) 80 60 *RoHS Directive 2002/95/EC Jan. 27, 2003 including 40 annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. 20 The device characteristics and parameters in this data sheet can and do vary in different applications and 0 actual device performance may vary over time. -55 070 155 Users should verify actual device performance in their Ambient Temperature (C) specific applications. *RoHS COMPLIANT VERSIONS AVAILABLE *RoHS COMPLIANT LEAD FREE LEAD FREE VERSIONS ARE RoHS COMPLIANT* Rated Power (%) CR0603/CR0805/CR1206 - Chip Resistors Performance Characteristics Test Limits DR Test Procedure Method Specification 1 % 5 % MIL-STD-202 303 DC Resistance -- MIL-R-55342D 4.7.2 1 % 5.0 % EIA RS-396 4.4 Low Temperature -55 C, 1 hour OFF MIL-R-55342D 4.7.4 MIL-R-55342D 4.7.4 (0.5 % + 0.05 ) (1.0 % + 0.05 ) Operation 45 minutesO EIA RS-396 4.6 Rated Voltage x 2.5, 5 seconds: Short time MIL-R-55342D 4.7.5 CR0603: 100 V max. MIL-R-55342D 4.7.5 (1 % + 0.05 ) (2 % + 0.05 ) Overload EIA RS-396 4.7 CR0805: 300 V max. CR1206: 400 V max. High Temperature MIL-R-55342D 4.7.6 +125 C, 1000 hours MIL-R-55342D 4.7.6 (1.0 % + 0.05 ) +(2.0 % + 0.1 ) Exposure EIA RS-396 4.8 Resistance to 260 C, 10 seconds MIL-R-55342D 4.7.7 MIL-R-55342D 4.7.7 (0.5 % + 0.05 ) (1.0 % + 0.05 ) Solder Heat Moisture Resis- MIL-STD-202 106D 90-98 % RH, 10 cycles MIL-R-55342D 4.7.8 (0.5 % + 0.05 ) (2.0 % + 0.05 ) tance EIA RS-396 4.9 MIL-STD-202 108 +70 C 1.5 hours ON, Load Life Condition D MIL-R-55342D 4.7.10 (1.0 % + 0.05 ) (3.0 % + 0.1) 0.5 hours OFF 1000 hours EIA RS-396 4.12 MIL-STD-202 208 Solderability +235 C 3 seconds MIL-R-55342D 4.7.11 95 % of area covered EIA RS-396 4.11 Terminal Strength Pull Test MIL-R-55342D 4.7.12 MIL-R-55342D 4.7.12 500 g R1 kW 1 mV/V max. R10 kW 3 mV/V max. Current Noise Quan-Tech Model 315B MIL-STD-202 308 MIL-R-55342D 6.6 R100 kW 6 mV/V max. R1 MW 10 mV/V max. Humidity, Steady +40 C 90-95 % RH, MIL-STD-202 103B -- (2.5 % + 0.05 ) (2.5 % + 0.05 State 1344 hours Condition D MIL-STD-202 101D Salt Spray 96 hours -- (1.0 % + 0.2 ) (1.0 % + 0.1 Condition A Vibration 10-2000 Hz, 6 hours MIL-STD-202 201A -- (0.5 % + 0.1 ) (1.0 % + 0.1 Voltage Coefficient -- MIL-STD-202 309 -- 100 ppm/V Insulation Resis- Test potential: 500V MIL-STD-202 302 -- 1 G tance CR0603: 100 V Condition B Dielectric With- CR0805, CR1206: 500 V -- MIL-STD-202 301 -- standing Voltage CR0603: 300 V Drop Test 1 m MIL-STD-202 203B -- (0.5 % + 0.1 ) (1 % + 0.1 Bending Test 5 mm/90 mm, 10 seconds -- -- (1 % + 0.05 ) (1 % + 0.05 ) -55 C for 30 minutes, Thermal Shock +155 C for 30 minutes, IEC 60115-1-4.19 -- (0.5% + 0.05 ) (1 % + 0.05 ) 5 cycles Resistance to Dry 125 5 C for 96 4 hours IEC 60115-1-4.23.2 -- (1 % + 0.05 ) (2 % + 0.1 ) Heat Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications.