EPS1D-F19-AE0024L Bourns

Features Incrementalencoder/momentarypushswitchoption Longoperatinglife Sturdyconstruction Snap-inmount EPS - Digital Contacting Encoder With Momentary Switch Option Electrical Characteristics Output...................................................................................2-bit quadrature code, Channel A leads Channel B by 90 electrically turning clockwise (CW) Closed Circuit Resistance ...........................................................................................................................................................................5 ohms maximum Open Circuit Resistance........................................................................................................................................................................500 K ohms minimum Contact Rating...................................................................................................................................................10 milliamp 10 VDC or 0.1 watt maximum Insulation Resistance (500 VDC) ...................................................................................................................................................1,000 megohms minimum Dielectric Withstanding Voltage (MIL-STD-202 Method 301) Sea Level.............................................................................................................................................................................................1,000 VAC minimum Electrical Travel ..................................................................................................................................................................................................... Continuous Contact Bounce (15 RPM)................................................................................................................................................................ 5 milliseconds maximum RPM (Operating) 120 maximum Encoder Switching Configuration (applies to detented version only) .............................................................................................................. Normally Open Phase Tolerance (CH A to CH B).............................................................................................................................................................................90 72 Environmental Characteristics Operating Temperature Range....................................................................................................................................... +1 C to +85 C (+34 F to +185 F) Storage Temperature Range .......................................................................................................................................... -40 C to +85 C (-40 F to +185 F) Humidity..................................................................................................................................................................MIL-STD-202, Method 103B, Condition B Vibration ...........................................................................................................................................................................................................................15 G Contact Bounce ...........................................................................................................................................................................0.1 millisecond maximum Shock................................................................................................................................................................................................................................50 G Contact Bounce ...........................................................................................................................................................................0.1 millisecond maximum Rotational Life.................................................................................................................................................................................. 200,000 shaft revolutions Switch Life ....................................................................................................................................................................................................... 100,000 cycles IP Rating.......................................................................................................................................................................................................................... IP 40 Mechanical Characteristics Mechanical Angle .........................................................................................................................................................................................360 Continuous Running Torque ...............................................................................................................................................................0.5 to 1.5 N-cm (0.75 to 2.25 oz-in.) Mounting Torque.............................................................................................................................................................56 to 79 N-cm (5-7 lb.-in.) maximum Shaft Side Load (Static)..................................................................................................................................................................4.53 kg (10 lbs.) minimum Weight .................................................................................................................................................................................Approximately 21 gms. (0.75 oz.) Terminals ..................................................................................................................................................................................Printed circuit board terminals Soldering Condition .................................................................... Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 wire diameter. Maximum temperature 399 C (750 F) for 5 seconds, no wash process to be used with no clean flux. Part can be wave soldered at 260 C (500 F) for 5 seconds, no wash process with no clean flux. Marking...............................................................................................................................................Manufacturers name and part number, and date code Hardware.......................................................One lockwasher and one mounting nut supplied with each encoder, except where noted in the part number. Switch Characteristics Switch Type ...............................................................................................................................................................................Push Momentary, SPST N.O. Power Rating (Resistive Load).................................................................................................................................................... 10 milliamps 12 volts DC Closed Switch Resistance........................................................................................................................... Less than 200 ohms 440 gram force on shaft Switch Travel ................................................................................................................................................................................................... 2.25 0.25 mm Switch Actuation Force............................................................................................................................................................... 370 70 grams (5 1 oz.-in.) This table is intended to show available outputs as currently defined. Quadrature Output Table - FULL CYCLE PER DETENT RECOMMENDED INCREMENTAL CONTROL DIAGRAM (Normally Open in Detent Shown) FOR USE WITH A DEBOUNCE CIRCUIT (CUSTOMER LOGIC CIRCUITRY) FULL CYCLE PER DETENT (Normally Open in Detent Shown) 7 9 CW Channel A DIRECTION Closed Circuit 5 ms DELAY Open Circuit DECODE UP/DOWN BINARY DEBOUNCE Closed Circuit LOGIC COUNTER OUTPUT (MC 14490) Open Circuit MAGNITUDE DD D D D Channel B CCW *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specications are subject to change without notice. Users should verify actual device performance in their specic WARNING Cancer and Reproductive Harm applications. The products described herein and this document are subject to specic legal disclaimers as set forth on the www.P65Warnings.ca.gov last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. *RoHS COMPLIANT VERSIONS AVAILABLEEPS-DigitalContactingEncoderWithMomentarySwitchOption Product Dimensions SNAP-IN MOUNTING - S style bushing / F style shaft 15.2 (.598) 8.20 19.0 (.323) (.748) 5.35 (.211) 2.00 3.17 (.125) 2.26 (.079) (.089) 4.01 (.158) 4.800 DIA. 8.13 (0.189) (.320) 1.60 26.97 (.063) (1.061) 4.32 (.170) 2.50 2X DIA. (.098) 2.00 +0.5/-0.0 (.078 +.020/-0.0) x x x x x TOTAL ACTUATION TRAVEL 22.20 0.50 (.874) 2X X 45 (.020) 3.60 CHAMFER (.142) 0.25 (.010) 7.50 (.300) 8.00 PCB MOUNTING DIMENSIONS (.315) 9.00 (.354) 9.85 2X (.388) 9.34 0.97 2.70 2X 4X RADIUS 2X DIA. 0.50 (.368) (.038) 0.75 (.106) X 45 CHAMFER M9 X 6 g (.020) (.030) 18.0 25.00 DIA. 24.33 (.710) 10.50 (.984) 22.20 (.958) 23.00 DIA. DIA. (.413) (.874) (.905) 5.97 3.97 4.63 (.235) (.156) (.182) 1.10 2X (.043) 6.50 0.80 2X PIN 1 (.260) (.031) 2.54 TYP 1.06 5X (.100) (.042) MM DIMENSIONS: (IN) 1 TOLERANCES: EXCEPT WHERE NOTED 2 CHANNEL B .51 .13 DECIMALS: .XX .XXX 3 COMMON (.020) (.005) 4 CHANNEL A 5 TERMINAL PIN NO. Specications are subject to change without notice. Users should verify actual device performance in their specic applications. The products described herein and this document are subject to specic legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.