Features Carbonelement Plainorknurledshaftoption Metal bushing/metal shaft Centerdetentstandard RearsolderlugsorPCpins 250Kand500Kstandardresistancevalues StandardMandNtaper RoHS compliant* PDB182-GTRB - 17 mm Blend-Balance Guitar Potentiometer Product Dimensions Electrical Characteristics PDB182-GTRB1, PDB182-GTRB3, Taper...................................... Linear, audio PDB182-GTRB2 PDB182-GTRB4 Standard Resistance Range 11.3 19.0 ...............................250K to 500K ohms 11.3 19.0 6.0 6.0 (.445) (.748) (.445) (.748) Standard Resistance Tolerance....... 20 % (.236) (.236) 9.5 Residual Resistance................... 1 % max. 1.0 (.374) 1.5 9.5 (.039) (.059) 1.0 (.374) 6.00 Environmental Characteristics (.039) 16.5 (.236) 1.5 (.650) 6.0 DIA. (.059) Operating Temperature.... -10 C to +50 C (.236) 11.5 KNURLED Power Rating DIA. SHAFT (.453) KNURLED Dual Section ............................0.06 watt 13.00 C0.5 SHAFT Maximum Operating Voltage (.512) 18 TEETH 3/8NEF Audio .............................................150 V C0.5 R2 R1 18 TEETH Sliding Noise ...........................47 mV max. 7.7 3/8NEF (.303) 14.8 Mechanical Characteristics R2 R1 (.583) DIA. 6.00 5.0 Mechanical Angle.......................300 5 1.5 3.0 1.0 3.5 (.236) (.197) Rotational Torque ............. 10 to 150 gf-cm (.059) (.118) (0.39) (.138) PLAIN 16.2 Detent Torque................... 50 to 300 gf-cm SHAFT (.638) Stop Strength ........................5 kg-cm min. 2.5 Rotational Life ......................15,000 cycles (.098) 5.0 (.197) Soldering Condition Manual/Wave 17.0 DIA. 17.0 (.669) ........... 260 C max. for 3 seconds max. DIA. FULL CW (.669) Wash.........................Not recommended FULL 30 10 30 10 Hardware....................One flat washer and CW POSITION mounting nut supplied per potentiometer with bushing Standard Resistance Table 13.00 Resistance Resistance (.512) (Ohms) Code 250,000 254 1 2 3 5.0 5.0 500,000 504 (.197) (.197) 12 3 5.0 5.0 How to Order NUT WASHER 3/8NEF (.197) (.197) 9.7 0.3 (.382 .012) PDB18 2 - GTR B1 - 254 MN DIA. Model Number of Sections 2 = Dual Section Guitar Pot Designator 11.0 0.5 2.3 0.2 12.0 0.5 DIA. (.433 .020 (.091 .008) (.472 .020) Configuration B1 = Knurled Shaft/Solder Lugs/ Center Detent B2 = Plain Shaft/Solder Lugs/ TOLERANCES: Center Detent 10.0 0.3 10.0 ~ 100 0.5 = = B3 = Knurled Shaft/PC Pins/ UNDER (.394) (.012) (.394 ~ 3.937) (.020) Center Detent B4 = Plain Shaft/PC Pins/ Center Detent Resistance Code (See Table) Resistance Taper (See Taper Chart) WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specications are subject to change without notice. Users should verify actual device performance in their specic applications. The products described herein and this document are subject to specic disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. *RoHS COMPLIANTPDB182-GTRB - 17 mm Blend-Balance Guitar Potentiometer Taper Chart Circuit Derating Curve 2 Dual Gang M and N Taper 100 100 N(2H) M(1H) 80 R1 1 3 90 60 80 40 33 70 R2 1 3 20 60 0 M(1H) N(2H) 0 10 20 30 40 50 60 70 80 90 100 2 50 Ambient Temperature (C) 40 30 20 10 010 20 30 40 50 60 70 80 90 100 Term 1 Rotational Travel (%) Term 3 NOTE: Resistance characteristic of curve N is plotted with respect to terminal 3 Asia-Pacific: Tel: +886-2 2562-4117 Email: asiacus bourns.com EMEA: Tel: +36 88 885 877 Email: eurocus bourns.com The Americas: Tel: +1-951 781-5500 Email: americus bourns.com www.bourns.com REV. 10/19 Specications are subject to change without notice. Users should verify actual device performance in their specic applications. The products described herein and this document are subject to specic legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Taper M: Output voltage across term. 1-2 X 100 (%) Input voltage across term. 1-3 Taper N: Output voltage across term. 2-3 X 100 (%) Input voltage across term. 1-3 Rating Power Ratio (%)