TISP7038L1DR-S Bourns

TISP7015L1, TISP7038L1 TRIPLE ELEMENT THYRISTOR OVERVOLTAGE PROTECTORS TISP70xxL1 (VLV) Overvoltage Protectors Three Terminal Very Low Voltage (VLV) Protection Agency Recognition Ion-Implanted Breakdown Region Description V V DRM (BO) Device UL File Number: E215609 V V 7015L1 8 15 D Package (Top View) 7038L1 28 38 T1 1 8 NC Protection for Signal, Data and Control Lines - ISDN 2 7 NC NC - T1/E1 3 6 - Ethernet NC G - RS232 & RS485 T2 4 5 NC MD7XAJA Low Capacitance - 7015L1 ....................................................................... 24 pF typ. NC - No internal connection - 7038L1 ....................................................................... 17 pF typ. Rated for International Surge Wave Shapes Device Symbol T2 T1 I Voltage PPSM Standard Waveshape A 2/10 GR-1089-CORE 200 1.2/50 IEC 61000-4-5 100 TIA/EIA-IS-968 10/700 50 ITU-T K.20/45/21 10/1000 GR-1089-CORE 30 IEC 61000-4-2 Immunity Ratings SD7XAD Contact .................................................................................. 6 kV G Air ........................................................................................... 8 kV Description The TISP70xxL1 series are 3-point overvoltage protectors designed for protecting against metallic (transverse mode) and simultaneous longitudinal (common mode) impulses. Each terminal pair has the same voltage limiting values and surge current capability. These devices are designed to limit overvoltages between signal, data and control port conductors, connected to terminals T1 and T2, and a protective ground, G. Each terminal pair has a symmetrical voltage-triggered bidirectional thyristor characteristic (Figure 1). Overvoltages are initially clipped by breakdown clamping until the voltage rises to the breakover level, which causes the device to crowbar into a low-voltage on state. This low-voltage on state causes the current resulting from the overvoltage to be safely diverted through the device. The device holding current will normally be higher than the available short circuit d.c. system current, causing the protector to switch off as the diverted current subsides. How to Order ... UL Recognized Components Device Package Carrier Order As TISP7015L1 D (8-pin, Small-outline) R (Embossed Tape Reeled) TISP7015L1DR-S TISP7038L1 D (8-pin, Small-outline) R (Embossed Tape Reeled) TISP7038L1DR-S JULY 2000 REVISED JULY 2019 *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. WARNING Cancer and Reproductive Harm The products described herein and this document are subject to specific legal disclaimers as set forth on the last www.P65Warnings.ca.gov page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. TISP70xxL1 (VLV) Overvoltage Protectors The TISP70xxL1 is guaranteed to withstand the listed international ESD (ElectroStatic Discharge), and lightning impulses in both polarities. Terminals marked NC do not have any internal connections and may be left floating or tied to some circuit point. The TISP7038L1 is a functional replacement for the TPN3021. Absolute Maximum Ratings, T = 25 C (Unless Otherwise Noted) J Rating Symbol ValueUnit TISP7015L1 8 Repetitive peak off-state voltageV V DRM TISP7038L1 28 Non-repetitive peak on-state pulse current(see Notes 1 and 2) 2/10 (Telcordia GR-1089-CORE, 2/10 voltage wave shape) 200 1/20 (ITU-T K.22, 1.2/50 voltage wave shape, also VDE0878) 100 8/20 (IEC 61000-4-5, Figure 12 generator, 1.2/50 voltage wave shape) 100 I A PPSM 10/160 (TIA/EIA-IS-968 (formally FCC Part 68), 10/160 voltage wave shape) 75 5/310 (ITU-T k.20/21, 10/700 voltage wave shape, also IEC 61000-4-5 and VDE0433) 50 10/560 (TIA/EIA-IS-968 (formally FCC Part 68), 10/560 voltage wave shape) 40 10/1000 (Telcordia GR-1089-CORE, 10/1000 voltage wave shape) 30 Non-repetitive peak on-state current (see Note 1) 16.7 ms (60 Hz) full sine wave 9 20 ms (50 Hz) full sine wave 8 I A TSM 0.2 s 50 Hz/60 Hz a.c. 3 2.0 s 50 Hz/60 Hz a.c. 1.5 Junction temperature T -40 to +150 C J Storage temperature range T -65 to +150 C stg NOTES: 1. Initially the TISP70xxL1 must be in thermal equilibrium at the specified TA. The surge may be repeated after the TISP70xxL1 returns to its initial conditions. 2. These non-repetitive rated currents are peak values of either polarity. EMC Immunity Test Ratings, T = 25 C (Unless Otherwise Noted) A Rating Symbol ValueUnit Level 3 open-circuit voltage, IEC 61000-4-2, 2001-4, ESD generator, also ITU-T K.20 contact discharge 6 V kV O/C air discharge 8 Electrical Characteristics, T = 25 C (Unless Otherwise Noted) J Parameter Test Conditions Min Typ Max Unit Repetitive peak off- I V = V 4 A DRM D DRM state current TISP7015L1 15 V Breakover voltage dv/dt = 250 V/ms, R = 300 V (BO) SOURCE TISP7038L1 38 I Breakover current dv/dt = 250 V/ms, R = 300 300 mA (BO) SOURCE I Holding current IT = 5 A, di/dt = 30 mA/ms 30 mA H JULY 2000 REVISED JULY 2019 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.