FT900/1/2/3 Embedded Microcontroller Datasheet Version 1.1 Document No.: FT 000965 Clearance No.: FTDI 421 Future Technology Devices International Ltd. FT900/1/2/3 (Embedded Microcontroller) Two SPI slaves support single data transfer The FT90x series includes the FT900, with 25MHz clock. FT901, FT902 and FT903 which are 2 Two I C bus interfaces can be configured as complete System-On-Chip 32-bit RISC master or slave, which support standard / fast microcontrollers for embedded / fast plus / high speed mode data transfers. Max data transfer rate up to 3.4 Mbit/s. Clock applications featuring a high level of stretching is supported. integration and low power 2 I S bus interface can be configured as master consumption. It has the following or slave. Two clock input options (24.576 MHz features: 2 and 22.5792 MHz) to support I S master mode for different audio sample rates. High performance, low power 32-bit FT32 core processor, running at a frequency of 100MHz. UART interface can be configured as one full programmable UART0 or two simple interfaces, 256kB on-chip Flash memory. UART0 and UART1 with CTS / RTS control 256kB on-chip shadow program memory. function. True Zero Wait States (0WS) up to 3.1 DMIPS Four user timers with pre-scaling and a per MHz performance watchdog function. 64kB on-chip data memory. 8-bit parallel data interface supports camera data capturing. EFUSE for security configuration. Support 7 independent PWM channels. Channel Integrated Phase-Locked Loop (PLL) supports 0 and 1 can be configured as PCM 8-bit/16-bit external 12MHz crystal and direct external clock stereo audio output. source input. SD host controller is compatible to standard 32.768 kHz real time clock support. specification V3.0, it supports up to 25 MHz SD One USB2.0 EHCI compatible host controller clock speed and software supports SD card supports high-speed (480 Mbit/s), full-speed format in SD/SDHC/SDXC. (12 Mbit/s), and low-speed (1.5 Mbit/s). Support two 10-bit DAC 0/1 channels output, One USB2.0 peripheral controller supports high- sample rate at ~1 MS/s. speed (480 Mbit/s) and full-speed (12 Mbit/s). Support seven 10-bit ADC 1/7 channels input, USB2.0 host and peripheral controllers support sample rate is up to ~960 kS/s. the Isochronous, Interrupt, Control, and Bulk Single 3.3 volt power supply, built-in 1.2 V transfers. regulators. 10/100 Mbps Ethernet that is compliant with the 3.3 volt I/O power supply. IEEE 802.3/802.3u standards. (FT900 and FT901 only) Support USB Battery Charging Specification Rev 1.2. Downstream port can be configured as Supports One-Wire debugger for downloading SDP, CDP or DCP. Upstream port can perform firmware to Flash memory or shadow program BCD mode detection. memory, and supports a software debugger. Support VBUS power switching and over Two CAN controllers support CAN protocol 2.0 current control. parts A & B, data rate is up to 1 Mbit/s. (FT900 and FT902 only) Power-On Reset (POR). One SPI master supports single / dual / quad -40C to 85C extended operating temperature modes of data transfer. Clock rate is up to 25 range. MHz Available in compact Pb-free 100-Pin packages (all RoHS compliant). Copyright 2015 Future Technology Devices International Limited 1 FT900/1/2/3 Embedded Microcontroller Datasheet Version 1.1 Document No.: FT 000965 Clearance No.: FTDI 421 Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright 2015 Future Technology Devices International Limited 2