FT900/1/2/3 Revision C Embedded Microcontroller Datasheet Version 1.1 Document No.: BRT 000172 Clearance No.: BRT 087 Bridgetek Pte Ltd FT900/1/2/3 Revision C (Embedded Microcontroller) The FT90X series includes the FT900, FT901, FT902 Two SPI slaves support single data transfer and FT903 which are complete System-On-Chip 32- with 25MHz clock. bit RISC microcontrollers for embedded applications 2 Two I C bus interfaces (one master and one featuring a high level of integration and low power slave) which support standard / fast / fast plus consumption. It has the following features: / high speed mode data transfers of up to 3.4 High performance, low power 32-bit FT32 core Mbit/s. Clock stretching is supported. processor, running at a frequency of 100MHz. 2 I S bus interface can be configured as master 256kB on-chip Flash memory. or slave. Two clock input options (24.576 MHz 2 and 22.5792 MHz) to support I S master mode 256kB on-chip shadow program memory. for different audio sample rates. True Zero Wait States (0WS) up to 3.1 DMIPS UART interface can be configured as one full per MHz performance. programmable UART0 or two simple interfaces, UART0 and UART1 with CTS / RTS control 64kB on-chip data memory. function. OTP memory for security configuration. Four user timers with individual pre-scaler and Integrated Phase-Locked Loop (PLL) supports a watchdog function. external 12MHz crystal and direct external clock 8-bit parallel data interface supports camera source input. data capturing. 32.768 kHz Real Time Clock (RTC) support. Supports 7 independent PWM channels. Power-On Reset (POR). Channel 0 and 1 can be configured as PCM 8- bit/16-bit stereo audio output. One USB2.0 EHCI compatible host controller supports high-speed (480 Mbit/s), full-speed SD host controller is compliant with standard (12 Mbit/s), and low-speed (1.5 Mbit/s). specification V3.0/SDIO specification V2.0/MMC card specification V4.3. It supports up to 50 One USB2.0 device controller supports high- MHz SD clock speed and software supports SD speed (480 Mbit/s) and full-speed (12 Mbit/s). card format in SD/SDHC/SDXC. USB2.0 host and device controllers support the Supports two 10-bit DAC 0/1 channels output, Isochronous, Interrupt, Control, and Bulk sample rate at ~1 MS/s. transfers. Supports seven 10-bit ADC 1/7 channels input, USB2.0 device controller supports the high- sample rate is up to ~960 kS/s. bandwidth isochronous IN transaction. Single 3.3 volt power supply and built-in 1.2 V 10/100 Mbps Ethernet that is compliant with the regulators. IEEE 802.3/802.3u standards. (FT900 and FT901 only). 3.3 volt I/O power supply. Supports One-Wire debugger for downloading Supports USB Battery Charging Specification firmware to Flash memory or shadow program Rev 1.2. Downstream port can be configured as memory, and supports a software debugger. SDP, CDP or DCP. Upstream port can perform BCD mode detection. Two CAN controllers support CAN protocol 2.0 parts A & B, data rate is up to 1 Mbit/s. (FT900 Supports VBUS power switching and over and FT902 only). current control. One SPI master supports single / dual / quad -40C to 85C extended operating temperature modes of data transfer. The clock rate is up to range. 50 MHz. Available in compact Pb-free 100-Pin packages (all RoHS compliant). Copyright Bridgetek Pte Ltd 1 FT900/1/2/3 Revision C Embedded Microcontroller Datasheet Version 1.1 Document No.: BRT 000172 Clearance No.: BRT 087 Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Bridgetek Pte Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Bridgetek Pte Ltd, 178 Paya Lebar Road, 07-03, Singapore 409030. Singapore Registered Company Number: 201542387H Copyright Bridgetek Pte Ltd 2