FT905/6/7/8 Revision C Embedded Microcontroller Datasheet Version 1.0 Document Reference No.: BRT 000173 Clearance No.: BRT 100 Bridgetek Pte Ltd FT905/6/7/8 (Datasheet) The FT905/6/7/8 series includes the FT905, FT906, Two CAN controllers support CAN protocol2.0 FT907 and FT908 which are complete System-On- parts A&B, data rate is up to 1Mbit/s. (FT905 Chip 32-bit RISC microcontrollers for embedded and FT907 only). applications featuring a high level of integration One SPI master supports single / dual / quad and low power consumption. They have the modes of data transfer. Clock rate is up to 25 following features: MHz. High performance, low power 32-bit FT32core One SPI slave supports single data transfer processor, running at a frequency of 100MHz. with a 25MHz clock. 256kB on-chip Flash memory. 2 One I C interface which can be configured as a 256kB on-chip shadow program memory. master or a slave. It supports standard / fast / fast-plus / high speed mode data transfers of True Zero Wait States (0WS) up to 3.1 DMIPS up to 3.4 Mbit/s. Clock stretching is supported. per MHz performance. UART interface can be configured as one full 64kB on-chip data memory. programmable UART0 or two simple UART0 and UART1 with CTS / RTS control function only. Flash OTP memory for security configuration. Four user timers with pre-scaling and a Integrated Phase-Locked Loop (PLL) supports watchdog function. external 12MHz crystal and direct external clock source input. Supports 7 independent PWM channels. Channel 0 and 1 can be configured as PCM 8- 32.768 kHz Real Time Clock (RTC) support. bit/16-bit stereo audio output. One USB 2.0 EHCI compatible host controller Supports two 10-bit DACs 0/1 channels output, supports high-speed (480Mbit/s), full-speed sample rate at ~1 MS/s. (12Mbit/s), and low-speed (1.5Mbit/s). Supports four 8-bit/10-bit ADC 1/4 channels One USB 2.0 device controller supports high- input, sample rate is up to ~960 KS/s. speed (480Mbit/s) and full-speed (12Mbit/s). Single 3.3 volt power supply and built-in 1.2 V USB 2.0 host and device controllers support the regulators. Isochronous, Interrupt, Control, and Bulk transfers. 3.3 volt I/O power supply. Supports USB Battery Charging Specification Supports VBUS power switching and Rev 1.2. Downstream port can be configured as overcurrent control. SDP, CDP or DCP. Upstream port can perform BCD mode detection. Provides a Power-On Reset (POR) signal to indicate stable power regulator. 10/100Mbps Ethernet that is compliant with the IEEE 802.3/802.3u standards. (FT905 and -40C to 85C extended operating temperature FT906 only). range. Supports One-Wire debugger for downloading Available in compact Pb-free -76-pin (QFN) and firmware to Flash memory or shadow program 80-pin (LQFP) packages (all RoHS compliant). memory, and supports a software debugger. Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Bridgetek Pte Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Bridgetek Pte Ltd, 178 Paya Lebar Road, 07-03, Singapore 409030. Singapore Registered Company Number: 201542387H Copyright Bridgetek Pte Ltd 1 FT905/6/7/8 Revision C Embedded Microcontroller Datasheet Version 1.0 Document Reference No.: BRT 000173 Clearance No.: BRT 100 1 Typical Applications Home security system CCTV monitor Home Automation Industrial automation Embedded audio application Medical appliances Motor drive and application control Instrumentation E-meter DAQ System 1.1 Part Numbers Part Number Package 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, support both CAN Bus FT905Q-C-X and Ethernet features. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, support both CAN FT905L-C-X Bus and Ethernet features. 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, support Ethernet, FT906Q-C-X doesnt support CAN Bus. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, support Ethernet, FT906L-C-X doesnt support CAN Bus. 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, support CAN Bus, FT907Q-C-X doesnt support Ethernet. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, support CAN Bus, FT907L-C-X doesnt support Ethernet. 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, doesnt support either FT908Q-C-X CAN Bus or Ethernet features. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, doesnt support FT908L-C-X either CAN Bus or Ethernet features. Table 1-1 - FT905/6/7/8 Series Part Numbers Note: Packaging codes for x is: -R: Taped and Reel (qty per reel for LQFP is 1000 qty per reel for QFN is 3000) -T: Tray packing (qty per tray for LQFP is 160 qty per tray for QFN is 260) 1.2 USB 2.0 Compliant The FT905/6/7/8 series contains a USB 2.0 host controller and device controller that are both compliant with USB 2.0 specification. Copyright Bridgetek Pte Ltd 2