9000 Series Power Rocker and Lever Handle Switches Features/Benefits Typical Applications Thermoset UL 94V-0 housing Small equipment Rugged construction Shut-off switch Variety of actuator and termination options RoHS compliant UL 61058-1 Specifications Materials CONTACT RATING: CASE: Diallyl phthalate (DAP) (UL 94V-0). 9201 Model: ACTUATOR: Nylon, black standard. GP (general purpose) FRAME-REAR MOUNT OPTIONS: Spring steel, black. 6 AMPS 125 VAC 50/60 Hz T85 10,000 cycles (10E3) BUSHING: Brass, nickel plated. 3 AMPS 250 VAC 50/60 Hz T85 10,000 cycles HOUSING: Stainless steel. R (resistive) SWITCH SUPPORT: Brass or steel, matte-tin plated. 6 AMPS 30 VDC T85 10,000 cycles MOUNTING BRACKET: Stainless steel. 9221 Model: END CONTACTS: 9201 Model: Coin silver, silver plated. GP (general purpose) 9221 Model: Silver cadmium oxide. 10 AMPS 125 VAC 50/60 Hz T85 10,000 cycles CENTER CONTACTS: Copper alloy, silver plated 5 AMPS 250 VAC 50/60 Hz T85 10,000 cycles ALL TERMINALS: 9201 Model: Copper alloy, silver plated. R (resistive) 9221 Model: Copper alloy, matte-tin plated. 10 AMPS 30 VDC T85 10,000 cycles TERMINAL SEAL: Epoxy. ELECTRICAL LIFE: 25,000 make-and-break cycles at full load. HARDWARE: Nut, Screw & Lockwasher: Stainless steel. Standoff: CONTACT RESISTANCE: Below 10 m typ. initial Nylon standard, aluminum available, consult Customer 24 V DC, 100 mA. Service Center. 9 INSULATION RESISTANCE: 10 min. *Cadmium used in electrical contacts is acceptable for RoHS. DIELECTRIC STRENGTH: 2,500 Vrms min. sea level. NOTE: Any models supplied with Q contact material are RoHS compliant. OPERATING TEMPERATURE: 30C to 85C. NOTE: Specifications and materials listed above are for switches with standard options. SOLDERABILITY: Per MIL-STD-202F method 208D, or For information on specific and custom switches, consult Customer Service Center. EIA RS-186E method 9 (1 hour steam aging). Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages G-52 through G-55. For additional options not shown in catalog, consult Customer Service Center. Switch Function 9201 DP On-On, 6 Amps 9221 DP On-On, 10 Amps Actuator J1 Rocker J2 Lever Terminations J3 Rocker Z Solder lug (9201 only) J37 Rocker with metal frame AV2 Vertical right angle, PC thru-hole (9201 only) C PC Thru-hole (9201 only) Z4 Quick connect Contact Material Q Silver Seal E Epoxy D No Seal Actuator Color 2 Black 1 White Frame Color 3 Red 2 Black NONE No frame color required Dimensions are shown: Inches (mm) Specifications and dimensions subject to change G www.ckswitches.com G52 RockerRocker 9000 Series Power Rocker and Lever Handle Switches SWITCH FUNCTION SWITCH FUNCTION CONNECTED TERMINALS POS. 1 POS. 2 POS. 1 POS. 2 NO. POLES MODEL NO. RATING* SCHEMATIC 9201 6 AMPS ON ON DP 2-3,5-6 2-1,5-4 9221 10 AMPS ON ON DPDT DPDT .140 DIA.(3,56 ) w/ J10 actuator 1.875 1.625 (47,62) (41,28) w/ J10 w/ J10 actuator actuator Part number shown: 9201J1ZQE2 Terminal Nos. Molded On Side Of Case All 9000 Series models meet international dimensional and electrical requirements. * See CONTACT MATERIAL, page G-54, for complete ratings. 9221 model must be ordered with Z4 terminations and D seal option. ACTUATOR COLOR ACTUATORPANEL MOUNT ACTUATOR J1ROCKER OPTION ACTUATOR CODE COLOR 2 BLACK 1 WHITE 3 RED Finish: Matte. Other colors, custom actuator markings and legends available, consult Customer Service Center. NOTE: Hardware: two eachmounting screws, nuts, lockwashers and standoffs for 1/8 inch thick panel are supplied standard on all switches with panel mounting brackets. Actuators available separate- ly, see page G-55. Hardware available separately, see Technical Data section of this catalog. J2LEVER PANEL MOUNTING Dimensions are shown: Inches (mm) Specifications and dimensions subject to change G www.ckswitches.com G53