9000 Series
Power Rocker and Lever Handle Switches
Features/Benefits Typical Applications
Thermoset UL 94V-0 housing Small equipment
Rugged construction Shut-off switch
Variety of actuator and
termination options
RoHS compliant
UL 61058-1
Specifications Materials
CONTACT RATING: CASE: Diallyl phthalate (DAP) (UL 94V-0).
9201 Model: ACTUATOR: Nylon, black standard.
GP (general purpose)
FRAME-REAR MOUNT OPTIONS: Spring steel, black.
6 AMPS 125 VAC 50/60 Hz T85 10,000 cycles (10E3)
BUSHING: Brass, nickel plated.
3 AMPS 250 VAC 50/60 Hz T85 10,000 cycles
HOUSING: Stainless steel.
R (resistive)
SWITCH SUPPORT: Brass or steel, matte-tin plated.
6 AMPS 30 VDC T85 10,000 cycles
MOUNTING BRACKET: Stainless steel.
9221 Model:
END CONTACTS: 9201 Model: Coin silver, silver plated.
GP (general purpose)
9221 Model: Silver cadmium oxide.
10 AMPS 125 VAC 50/60 Hz T85 10,000 cycles
CENTER CONTACTS: Copper alloy, silver plated
5 AMPS 250 VAC 50/60 Hz T85 10,000 cycles
ALL TERMINALS: 9201 Model: Copper alloy, silver plated.
R (resistive)
9221 Model: Copper alloy, matte-tin plated.
10 AMPS 30 VDC T85 10,000 cycles
TERMINAL SEAL: Epoxy.
ELECTRICAL LIFE: 25,000 make-and-break cycles at full load.
HARDWARE: Nut, Screw & Lockwasher: Stainless steel. Standoff:
CONTACT RESISTANCE: Below 10 m typ. initial @
Nylon standard, aluminum available, consult Customer
24 V DC, 100 mA.
Service Center.
9
INSULATION RESISTANCE: 10 min.
*Cadmium used in electrical contacts is acceptable for RoHS.
DIELECTRIC STRENGTH: 2,500 Vrms min. @ sea level.
NOTE: Any models supplied with Q contact material are RoHS compliant.
OPERATING TEMPERATURE: 30C to 85C.
NOTE: Specifications and materials listed above are for switches with standard options.
SOLDERABILITY: Per MIL-STD-202F method 208D, or
For information on specific and custom switches, consult Customer Service Center.
EIA RS-186E method 9 (1 hour steam aging).
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown
and described on pages G-53 through G-56. For additional options not shown in catalog, consult Customer Service Center.
Switch Function
9201 DP On-On, 6 Amps
9221 DP On-On, 10 Amps
Actuator
J1 Rocker
J2 Lever
Terminations
J3 Rocker
Z Solder lug (9201 only)
J37 Rocker with metal frame
AV2 Vertical right angle, PC thru-hole (9201 only)
C PC Thru-hole (9201 only)
Z4 Quick connect
Contact Material
Q Silver
Seal
E Epoxy
D No Seal
Actuator Color
2 Black
1 White
Frame Color
3 Red
2 Black
NONE No frame color required
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
G
www.ck-components.com
G52
RockerRocker
9000 Series
Power Rocker and Lever Handle Switches
SWITCH FUNCTION
SWITCH FUNCTION CONNECTED TERMINALS
POS. 1 POS. 2 POS. 1 POS. 2
NO.
POLES MODEL NO. RATING* SCHEMATIC
9201 6 AMPS ON ON
DP 2-3,5-6 2-1,5-4
9221 10 AMPS ON ON
DPDT
DPDT
.140 DIA.(3,56)
w/ J10 actuator
1.875
1.625
(47,62)
(41,28)
w/ J10
w/ J10
actuator
actuator
Part number shown: 9201J1ZQE2 Terminal Nos.
Molded On Side Of Case
All 9000 Series models meet international dimensional and electrical requirements.
* See CONTACT MATERIAL, page G-55, for complete ratings.
9221 model must be ordered with Z4 terminations and D seal option.
ACTUATOR COLOR
ACTUATORPANEL MOUNT
ACTUATOR
J1 ROCKER
OPTION ACTUATOR
CODE COLOR
2 BLACK
1 WHITE
3 RED
Finish: Matte. Other colors, custom actuator
markings and legends available, consult
Customer Service Center.
NOTE: Hardware: two eachmounting screws, nuts,
lockwashers and standoffs for 1/8 inch
thick panel are supplied standard on all switches with
panel mounting brackets. Actuators available separate-
ly, see page G-55-56. Hardware available separately,
see Technical Data section of this catalog.
J2 LEVER
PANEL MOUNTING
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
G
www.ck-components.com
G53