BD Series
Standard Profile DIP Switches
Features/Benefits Typical Applications
Traditional full profile DIP switch Address switch for industrial controls
Extended actuator for easy actuation Logic switching for computers and peripherals
Open bottom construction allows for Function controlling for
H
solder washing without the need numerous applications
for tape seal
RoHS compliant
Specifications VIBRATION: No contact opening greater than 10 microseconds and no
contact closure when exposed to vibration .06 in DA or 5g,
SWITCH FUNCTION: SPST - 1 thru 12 position available whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz.
(except 11 position).
SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E
method 9 (1 hour steam aging).
CONTACT RATING:
PACKAGING: Switches supplied in rigid dispensing tubes in full-tube
Carry: 100 mA max. @ 50 V DC.
quantities only: this may effect order quantity. Number of switches
Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC.
per tube varies with model. Switch position 1 denotes pin number
MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break
1. All switch actuators in OFF position, standard.
cycles at full load, each circuit.
CONTACT RESISTANCE: Below 50 milliohms typ. initial Materials
@ 2-4 V DC 100mA. CASE & COVER: Glass filled polyester (PBT),
9
INSULATION RESISTANCE: 10 ohms min. flame retardant (UL 94V-0).
DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between
ACTUATOR: Glass filled nylon 6/6, flame retardant,
adjacent terminals.
heat stabilized (UL 94V-0)
CAPACITANCE: 5pF max. between adjacent terminals.
CONTACTS: Gold over nickel over phosphor bronze.
STORAGE & OPERATING TEMPERATURE: -40C to 85C.
TERMINALS: Matte-tin over nickel over phosphor bronze.
SHOCK: Withstands 20g 11 ms sawtooth waveform with no con-
tact opening greater than 10 microseconds. Note: Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Vertical Full Profile DIP
QUANTITY
PART NUMBER NO.POS. DIM. A PER TUBE
.038 TYP.
.062 BD01 1 .180 (4,57) 115
(0,97)
(1,58) MAX
BD02 2 .280 (7,11) 74
.100 TYP.
ACTUATOR
DIM 'A'
(2,54)
BD03 3 .380 (9,65) 54
TRAVEL
O
N BD04 4 .480 (12,19) 43
.380
.297 BD05 5 .580 (14,73) 35
(9,65)
(7,55)
BD06 6 .680 (17,27) 30
BD08
1 2345678
BD07 7 .780 (19,81) 26
.160 TYP.
BD08 8 .880 (22,35) 23
DIM 'B'
(4,06)
BD09 9 .980 (24,89) 21
.059 TYP.
(1,5)
.080 TYP.
BD10 10 1.080 (27,43) 19
(2,03)
BD12 12 1.280 (32,51) 16
.265
.032
Schematic
.030 (6,73)
(0,82)
(0,77)
TYP.
SPST
.007
.089
.020 TYP.
.100 TYP. (0,18)
.297
(2,26)
(0,51)
(2,54)
(7,55)
.141 TYP.
(3,58)
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
www.ck-components.com
H16
DIPDIP
BD Series
Standard Profile DIP Switches
Open Base and AV Right Angle Terminal Style
0.050 .089
(1,27) (2,26)
QUANTITY
s 0.030
PART NUMBER NO.POS. DIM. A PER TUBE
(0,77)
H
BD02AV 2 .280 (7,11) 72
0.297
BD03AV 3 .380 (9,65) 52
(7,55)
BD08AV
BD04AV 4 .480 (12,19) 42
0.061 TYP.
BD05AV 5 .580 (14,73) 35 .032
(1,55) (0,82)
BD06AV 6 .680 (17,27) 29
TYP.
DIM.A
BD07AV 7 .780 (19,81) 26
ON
BD08AV 8 .880 (22,35) 23
.080
BD09AV 9 .980 (24,89) 20 .380
(2,03)
(9,65)
BD10AV 10 1.080 (27,43) 18
.125
1 2 3 4 5 6 7 8
BD12AV 12 1.280 (32,51) 15
(3,18)
Schematic
.020 TYP.
.010
.100 TYP.
(0,51)
.007 (0,25)
(2,54)
(0,18)
.100
.320 .100
(2,54)
SPST (8,12)
(2,54)
.100 TYP.
.046 DIA TYP.
(2,54)
(1,17)
Installation, Soldering and Cleaning
All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps,
tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent
solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions:
1) Wave soldering recommended at 500 F (260C) solder temperature.
2) Hand solder using 30 watt small tip iron controlled at 500 F (260C), 10 seconds max./terminal.
3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method.
DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out.
4) All switch actuators must be in OFF position during soldering and cleaning processes.
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
www.ck-components.com
H17