BD Series Standard Profile DIP Switches Features/Benefits Typical Applications Traditional full profile DIP switch Address switch for industrial controls Extended actuator for easy actuation Logic switching for computers and peripherals Open bottom construction allows for Function controlling for H solder washing without the need numerous applications for tape seal RoHS compliant Specifications VIBRATION: No contact opening greater than 10 microseconds and no contact closure when exposed to vibration .06 in DA or 5g, which- SWITCH FUNCTION: SPST - 1 thru 12 position available ever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz. (except 11 position). SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CONTACT RATING: PACKAGING: Switches supplied in rigid dispensing tubes in full-tube Carry: 100 mA max. 50 V DC. quantities only: this may effect order quantity. Number of switches Switch: 100 mA max. 5 V DC or 25 mA max. 25 V DC. per tube varies with model. Switch position 1 denotes pin number MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break 1. All switch actuators in OFF position, standard. cycles at full load, each circuit. CONTACT RESISTANCE: Below 50 milliohms typ. initial Materials 2-4 V DC 100mA. CASE & COVER: Glass filled polyester (PBT), 9 INSULATION RESISTANCE: 10 ohms min. flame retardant (UL 94V-0). DIELECTRIC STRENGTH: 500 V RMS min. sea level between ACTUATOR: Glass filled nylon 6/6, flame retardant, adjacent terminals. heat stabilized (UL 94V-0) CAPACITANCE: 5pF max. between adjacent terminals. CONTACTS: Gold over nickel over phosphor bronze. STORAGE & OPERATING TEMPERATURE: -40C to 85C. TERMINALS: Matte-tin over nickel over phosphor bronze. SHOCK: Withstands 20g 11 ms sawtooth waveform with no con- tact opening greater than 10 microseconds. Note: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Vertical Full Profile DIP QUANTITY PART NUMBER NO.POS. DIM. A DIM. B PER TUBE .062 .038 TYP. BD01 1 .180 (4,57) NA 115 (0,97) (1,58) MAX BD02 2 .280 (7,11) .100 (2,54) 74 .100 TYP. ACTUATOR DIM A (2,54) BD03 3 .380 (9,65) .200 (5,08) 54 TRAVEL ON BD04 4 .480 (12,19) .300 (7,62) 43 .380 BD05 5 .580 (14,73) .400 (10,16) 35 .297 (9,65) (7,55) BD06 6 .680 (17,27) .500 (12,75) 30 BD08 1 2 34567 8 BD07 7 .780 (19,81) .600 (15,24) 26 .160 TYP. BD08 8 .880 (22,35) .700 (17,78) 23 DIM B (4,06) BD09 9 .980 (24,89) .800 (20,32) 21 .059 TYP. (1,5) .080 TYP. BD10 10 1.080 (27,43) .900 (22,.86) 19 (2,03) BD12 12 1.280 (32,51) 1.100 (27,94) 16 .265 .032 Schematic .030 (6,73) (0,82) (0,77) TYP. SPST .006 .089 .020 TYP100 TYP. (0,16) .297 (2,26) (0,51) (2,54) (7,55) .141 TYP. (3,58) Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com H16 DIPDIP BD Series Standard Profile DIP Switches Open Base and AV Right Angle Terminal Style 0.050 .089 (1,27) (2,26) QUANTITY 0.030 PART NUMBER NO.POS. DIM. A PER TUBE (0,77) H BD02AV 2 .280 (7,11) 72 0.297 (7,55) BD03AV 3 .380 (9,65) 52 BD08AV BD04AV 4 .480 (12,19) 42 0.061 TYP032 BD05AV 5 .580 (14,73) 35 (1,55) (0,82) BD06AV 6 .680 (17,27) 29 TYP. DIM.A BD07AV 7 .780 (19,81) 26 ON BD08AV 8 .880 (22,35) 23 .080 .380 BD09AV 9 .980 (24,89) 20 (2,03) (9,65) BD10AV 10 1.080 (27,43) 18 .125 1 2 3 4 5 6 7 8 BD12AV 12 1.280 (32,51) 15 (3,18) Schematic .020 TYP010 (0,51) .100 TYP. (0,25) .006 (2,54) (0,16) .100 .320 .100 (2,54) SPST (8,12) (2,54) .100 TYP046 DIA TYP. (2,54) (1,17) Installation, Soldering and Cleaning All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions: 1) Wave soldering recommended at 500 F (260C) solder temperature. 2) Hand solder using 30 watt small tip iron controlled at 500 F (260C), 10 seconds max./terminal. 3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method. DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out. 4) All switch actuators must be in OFF position during soldering and cleaning processes. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change www.ckswitches.com H17