BDB Series Standard Profile DIP Switches Features/Benefits Typical Applications Traditional full profile DIP switch Address switch for industrial controls Extended actuator for easy actuation Logic switching for computers and peripherals Special sealed construction allows for Function controlling for H solder washing without the need for numerous applications tape seal RoHS compliant New generation price competitive Specifications VIBRATION: No contact opening greater than 10 microseconds and no contact closure when exposed to vibration .06 in DA or 5g, which- SWITCH FUNCTION: SPST - 2 thru 12 position available ever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz. (except 11 position). SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CONTACT RATING: PACKAGING: Switches supplied in rigid dispensing tubes in full-tube Carry: 100 mA max. 50 V DC. quantities only: this may effect order quantity. Number of switches Switch: 100 mA max. 5 V DC or 25 mA max. 25 V DC. per tube varies with model. Switch position 1 denotes pin number MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break 1. All switch actuators in OFF position, standard. cycles at full load, each circuit. 2. Option for ON is available on volume demand. CONTACT RESISTANCE: Below 50 milliohms typ. initial Materials 2-4 V DC 100mA. 9 HOUSING: PA46, color red (UL94V-0) INSULATION RESISTANCE: 10 ohms min. ON BDB COVER: Glass filed polyester (PBT) (UL94V-0) DIELECTRIC STRENGTH: 300 V RMS min. sea level between adjacent terminals. ACTUATOR: Glass filed polyester (PBT) (UL94V-0) 1 23 4 5 6 7 8 CAPACITANCE: 5pF max. between adjacent terminals. CONTACTS: Gold plate phosphor bronze STORAGE & OPERATING TEMPERATURE: -40C to 85C. TERMINALS: Gold plate over nickel plated brass SHOCK: Withstands 20g 11 ms sawtooth waveform with no con- Note: Specifications and materials listed above are for switches with standard options. tact opening greater than 10 microseconds. For information on specific and custom switches, consult Customer Service Center. Vertical Full Profile DIP QUANTITY PART NUMBER NO.POS. DIM. A DIM. B PER TUBE BDB02 2 .280 (7,11) .100 (2,54) 70 BDB03 3 .380 (9,65) .200 (5,08) 51 ON BDB BDB04 4 .480 (12,19) .300 (7,62) 40 BDB05 5 .580 (14,73) .400 (10,16) 33 1 23 4 5 6 7 8 DATE CODE: YEAR+WEEK BDB06 6 .680 (17,27) .500 (12,75) 28 YEAR: The letter A means 2009, B means 2010..., J means 2018, and so on BDB07 7 .780 (19,81) .600 (15,24) 24 BDB08 WEEK: 01 means the rst week 01 means the second week, and so on BDB08 8 .880 (22,35) .700 (17,78) 21 BDB09 9 .980 (24,89) .800 (20,32) 19 BDB10 10 1.080 (27,43) .900 (22,.86) 17 BDB12 12 1.280 (32,51) 1.100 (27,94) 14 Schematic SPST DATE CODE: YEAR+WEEK YEAR: The letter A means 2009, B means 2010..., J means 2018, and so on WEEK: 01 means the rst week 01 means the second week, and so on Dimensions are shown: Inch (mm) Specifications and dimensions subject to change 21 aug 2018 www.ckswitches.com H22 NEW DIPDIP BDB Series Standard Profile DIP Switches Installation, Soldering and Cleaning All BDB Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions: H 1) Wave soldering recommended at 500 F (260C) solder temperature. 2) Hand solder using 30 watt small tip iron controlled at 500 F (260C), 10 seconds max./terminal. 3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method. DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out. 4) All switch actuators must be in OFF position during soldering and cleaning processes. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change 21 aug 2018 www.ckswitches.com H23 NEW