MP2060 Kool-Pak Clip Mount Power Film Resistor TO-220 Style Power Resistor Designed for Clip Mounting - Non-Inductive Up to 60 Watts continuous power at +25C case temperature, 0.020 and above. Up to 60 Amps continuous current at +25C case temperature, 0.015 and below. TO-220 Style package utilizes proven power semiconductor thermal solutions. Equivalent to UL94 V-0 flammability rating. Non-inductive design for high speed switching, snubbers and rf applications. Operation up to +150C case temperature. Electrically isolated case. Thermal Resistance Power Max. Current Max. Model Package Resistance R JC Rating Rating (Amps) Voltage Film (J) to Case (C) Current 60 A 0.005 18 Watts 6.94C/Watt rms * Limited Current 60 A 0.010 36 Watts 3.47C/Watt rms * Limited TO-220 MP2060 Style Current 60 A 0.015 54 Watts rms 2.31C/Watt * Limited These products are covered by one or more 250 V 0.020 to 1.00K I = P/R 60 Watts rms 2.08C/Watt * patents, also patents pending. Derating Curve Specifications: Derating Using Case Temperature (T ): 100 * C All power and associated overload ratings are 80 Temperature Coefficient: derated based upon case temperature using the 60 TC referenced to +25C, R taken at +150C derating curve. The case temperature is mea- 40 0.50 ohm and above, -20 to +80 ppm/C sured at the center of the ceramic mounting sur- 0.050 ohm to 0.49 ohm, 0 to +100 ppm/C 20 face, with the part properly mounted and under 0 0.015 ohm to 0.049 ohm, 0 to +200 ppm/C electrical load. Without a heat sink, when in free 25 100 150 0.005 ohm to 0.014 ohm, 0 to +300 ppm/C air at +25C, the MP2060 is rated for 2.5 watts. CASE TEMPERATURE, C Operating Temperature: -55C to +150C The thermal design should satisfy the following equation: Inductance: 10 nH typical in series when measured at Case Temperature (Tc) + Thermal Resistance (R ) x power applied (Watts) 150C, considering the full JC the shoulder of the lead. operating temperature range of the application. Capacitance: <1 pf typical without heat sink. Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material, such as thermal grease. The entire exposed ceramic portion must be in contact with the heat sink. When using a DWV: 1500 V AC isolation to the mounting surface rms spring clip, it is recommended that a mounting force of 8 to 30 pounds (35 to 130 N) be applied to the center of or a clip in contact with the top surface. the package. The clip should be round or smooth in the contact area to avoid concentrating the load on a small Insulation Resistance: 10,000 Megohms, min. point of the plastic body of the package. Another mounting option is to use a pressure bar method which can The resistor element is electrically isolated from the achieve a greater mounting force with a greater contact area. mounting surface. For additional applications information regarding mounting and pulse handling see the Caddock Applications Notes at caddock.com or contact Applications Engineering. Momentary Overload: 1.5 times rated power for 5 seconds, R (0.5 percent + 0.0005 ohm) max. Standard Resistance Values: 0.175 0.010 Load Stability: 2000 hours at rated power 0.410 0.010 (4.45 0.26) (10.41 0.26) Tolerance: 1% Standard (except as noted) R less than (1 percent +0.0005 ohm). 10.0 0.005 5% 0.33 100 Moisture Resistance: Mil-Std-202, Method 106, 0.010 2% 0.40 12.0 120 R (0.5 percent + 0.0005 ohm) max. 15.0 0.015 2% 0.50 150 0.640 0.010 0.020 0.75 20.0 200 Thermal Shock: Mil-Std-202, Method 107, (16.26 0.26) MP2060 25.0 0.025 1.00 250 Cond. F, R (0.5 percent + 0.0005 ohm) max. 50.0 0.150 0.030 0.030 1.50 27.0 300 1% (3.81 0.76) Shock: 100G, Mil-Std-202, Method 213, 30.0 0.033 2.00 330 Cond. I, R (0.4 percent + 0.0005 ohm) max. 0.040 2.50 33.0 400 0.100 0.020 (2.54 0.51) 40.0 0.050 3.00 470 Vibration, High Frequency: Mil-Std 202, 0.075 3.30 47.0 500 0.500 0.050 Method 204, Condition D, R (0.4 percent (12.70 1.27) 0.050 0.007 50.0 0.10 4.00 560 (1.27 0.18) + 0.0005 ohm) max. 0.15 5.00 56.0 750 75.0 0.20 7.50 1.00 K Terminal Strength: Mil-Std-202, Method 211, Cond. A 0.25 8.00 0.200 0.010 0.035 0.007 (Pull Test) 5 lbs., R (0.2 percent + 0.0005 ohm) max. (5.08 0.26) (0.89 0.18) 0.30 0.105 0.010 Terminal Material: Solderable For custom values and tolerances contact (2.67 0.26) DIMENSIONS IN INCHES AND (MILLIMETERS) Applications Engineering Measurement Note: Resistance measurements shall be made at 0.2 inch (5.08 mm) from the resistor body. Recommended Limitation of Use: Caddock does not recommend the MP2060 resistors for use in military or space applications. These products are recommended by Caddock for use only in Ordering Information: commercial/industrial applications. Caddock has qualified these products, for their intended use, to perform according to catalog specifications. Caddock does not maintain a military and/or space MP2060 - 0.050 - 1% level reliability program for these products. Caddock does not provide support for use of these Model Number: Tolerance products in military and space applications. These products have matte tin plated leads (with 100% Resistor Value: tin plating), there is no other lead finish offered for the MP2060 Resistors. Any use of these products in a military program, against this recommended limitation of use, will be completely supported by Packaging Information: MP2060 resistors are pack- the customer program design activity and component engineering activity based on their complete aged in plastic shipping tubes, 50 pieces per tube. These evaluation and testing, there will be no support provided by Caddock for this use. Space equipment resistors are available in a 50 piece minimum quantity and programs (both the engineering phase and the flight phase) must only use selected Caddock in full tube quantity increments (i.e. 50, 100, 150, etc.). products that have been purchased in accordance with NASA GSFC specifications. Applications Engineering Sales 17271 North Umpqua Hwy. 17271 N. Umpqua Hwy. ELECTRONICS, INC. Roseburg, Oregon 97470-9422 Roseburg, Oregon 97470-9422 Phone: (541) 496-0700 Phone: (541) 496-0700 e-mail: caddock caddock.com web: www.caddock.com Fax: (541) 496-0408 Fax: (541) 496-0408 For Caddock Distributors listed by country see caddock.com/contact/dist.html 2003-2007 Caddock Electronics, Inc. LOU-28 IL128.0708 RATED POWER %X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Thick Film Resistors - Through Hole category: Click to view products by Caddock manufacturer: Other Similar products are found below : M8340104M4701GCD03 M8340105K3300GGD03 M8340105K3922FGD03 M8340106K1002JCD03 M8340107K1002GGD03 M8340107K1152FGD03 M8340107K2701GCD03 M8340107M2002GCD03 M8340108K1000GCD03 M8340108K5601GCD03 M8340108M2203GCD03 M8340109K1002JCD03 M8340109K1003GCD03 M8340109K5101GGD03 FHV05010M0FKRB MP850-3.00-1% hte24511kf SM-SP093 ARC3.11 2M J A M8340105K1001GCD03 M8340105K3002GGD03 M8340105M1002JGD03 M8340107K2001GGD03 M8340107K4701GGD03 M8340107K5101GGD03 M8340107K5600GGD03 M8340108K4990FGD03 M8340108K49R9FGD03 M8340108M10R0GGD03 M8340109K2202GGD03 M8340109K5601GCD03 MOX-GRD-001 MOX-SP020 MOX-SP025E M8340107K2001GCD03 M8340102M4701GBD04 M8340102K1002GBD04 M8340102K1002GAD04 M8340109K2002GGD03 M8340108K22R0GGD03 M8340107M5100GGD03 OE1305 WMHP100-R22J M8340104K39R2FCD03 M8340106MA012JHD03 M8340107K1003GGD03 MS126-9.09K-0.1% MS126-249K-0.1% MS-221-82R5 MOX-750231004DE