C107-35 Calmark

SERIES 107 ALUMINUM INSERTER - EXTRACTOR Calmark offers the Series 107 Aluminum Inserter-Extractor for safe and easy insertion and extraction of printed circuit boards in the most severe applications. This product series offer a wide range of inserter-extractor with varying features from mechanical advantage ratios, color, board thickness, etc. If you don t see one here that meets your requirements, please contact our Applications Engineers with your specification. FEATURES n Ultra strong lever action design Series 107-50 - Inserter/Extractor (Aluminum) overcomes insertion and extraction forces of highest possible limits Series Feature Board Thickness Standard Mechanical Figures n Widths from 7.37 (.290) to 7.92 (.312) Color Advantage for printed circuit boards ranging 107-35 I E 1.6 (.063) black 5.5:1 1/A from 1.6 (.063) to 3.2 (.125) thick C107-35 I E 1.6 (.063) clear 5.5:1 1/A n Actuates from a simple U channel form 107-35-3 I E 2.4 (.093) black 5.5:1 1/A n Mounting detail on card retrofits C107-35-3 I E 2.4 (.093) clear 5.5:1 1/A other industry standards 107-35-4 I E 3.2 (.125) black 5.5:1 1/A n Available in black anodize or clear C107-35-4 I E 3.2 (.125) clear 5.5:1 1/A chemical film 107-50 I E 1.6 (.063) black 4.5:1 2/B n Generous area for identification C107-50 I E 1.6 (.063) clear 4.5:1 2/B markings 107-50-3 I E 2.4 (.093) black 4.5:1 2/B n Strong and Ultra-strong lever action C107-50-3 I E 2.4 (.093) clear 4.5:1 2/B overcome high insertion and 107-50-4 I E 3.2 (.125) black 4.5:1 2/B extraction forces C107-50-4 I E 3.2 (.125) clear 4.5:1 2/B n 107-73 and 107-75 offers a positive locking feature 107-51 I E 1.6 (.063) black 3.3:1 3/B C107-51 I E 1.6 (.063) clear 3.3:1 3/B MATERIALS/FINISH 107-51-3 I E 2.4 (.093) black 3.3:1 3/B C107-51-3 I E 2.4 (.093) clear 3.3:1 3/B EXTRACTOR 107-51-4 I E 3.2 (.125) black 3.3:1 3/B Aluminum alloy 6061-T6. Black anodize C107-51-4 I E 3.2 (.125) clear 3.3:1 3/B per Mil-A-8625, Type II Cl. 2. or Clear 107-55 I E 1.6 (.063) black 8:1 4/B chemical film per Mil-5541 Cl 3 for a conductive finish. Other anodize colors C107-55 I E 1.6 (.063) clear 8:1 4/B or a gold chemical film also available. 107-55-3 I E 2.4 (.093) black 8:1 4/B Please contact an Application Engineer C107-55-3 I E 2.4 (.093) clear 8:1 4/B with your requirements. 107-55-4 I E 3.2 (.125) black 8:1 4/B C107-55-4 I E 3.2 (.125) clear 8:1 4/B ROLL PIN Stainless steel, 2.38 (.094) x 6.35 107-73 I E L 1.6 (.063) black 4.2:1 5/C (.250) except all Series 107-35 C107-73 I E L 1.6 (.063) clear 4.2:1 5/C use 7.95 (.313) long . Roll pins 107-73-3 I E L 2.4 (.093) black 4.2:1 5/C are furnished with each inserter- C107-73-3 I E L 2.4 (.093) clear 4.2:1 5/C extractor. Series 107-73 and I E L 3.2 (.125) black 4.2:1 5/C 107-75, two roll pins 107-73-4 I E L 3.2 (.125) clear 4.2:1 5/C C107-73-4 I E L 1.6 (.063) black 7:1 6/C 107-75 I E L 1.6 (.063) clear 7:1 6/C C107-75 I E L 2.4 (.093) black 7:1 6/C 107-75-3 I E L 2.4 (.093) clear 7:1 6/C C107-75-3 I E L 3.2 (.125) black 7:1 6/C 107-75-4 I E L 3.2 (.125) clear 7:1 6/C C107-75-4 Feature: I = Inserter E = Extractor L = Latching For Pre-start pin feature, add P prefix to part number 66 www.calmark.com 800-854-7086SERIES 107 ALUMINUM INSERTER - EXTRACTOR 11.18 12.7 12.7 (.440) (5.00) (5.00) 9.91 (.390) 3.96 50.8 38.1 43.2 (.156) (2.00) (1.50) (1.70) R 3.96 (.156) 3.96 R (.156) 12.06 R 8.26 (.475) (.325) 12.06 7.37 (.475) (.290) 7.92 FIG. 1 FIG. 2 FIG. 3 7.37 (.312) (.290) 12.7 (5.00) 22.4 (.88) 22.4 (.88) 47.5 50.8 (1.87) (2.00) 12.06 (.475) 12.7 7.37 (5.00) (.290) 82.5 (3.25) 88.9 FIG. 5 (3.50) 12.06 (.475) 12.06 (.475) Units: mm (in) 12.7 Unless specified otherwise, .xx = .25, .x = .5 (5.00) 7.37 (.xxx = .010, .xx = .02) (.290) 7.37 FIG. 4 FIG. 6 (.290) Provides insertion and extraction travel of 7.6 (.30) min. Nominal position of card edge when seated in connector. The Inserter- Extractor will allow .76 (.03) overtravel APPLICATION DATA for tolerance take-up. 17.8 7.87 Two inserter or inserter-extractors are recommended per (.70) 1.02 (.040) Ref (.310) Card Guide printed circuit board taller than 127 (5) in height. 9.4 4.83 .25 (.109 .010) Surface (.37) 4.57 (.180) 2.36 .8 (.03) max. (.093) Dia. 4.3 (.17) min. Detail of Actuating Surfaces Units: mm (in) Required on Top and Bottom Guide Plates Unless specified otherwise, .xx = .25, .x = .5 FIG. A (.xxx = .010, .xx = .02) Provides insertion and extraction travel of 8.9 (.35) min. 22.86 .13 Provides insertion and extraction travel of 8.9 (.35) min. (.900 .005) Nominal position of card edge when 2.38 (.94) Dia. seated in connector. The Inserter- Nominal position of card edge when 2.77 Extractor will allow 1.3 (.05) overtravel seated in connector. The Inserter- (.109) 2.29 .13 for tolerance take-up. Extractor will allow 1.3 (.05) overtravel Dia. (.090 .005) for tolerance take-up. 6.35 (.250) 18.5 (.73) 7.24 .38 1.5 (.06) 6.35 7.24 .38 1.5 (.06) (.285 .015) Card Guide (.250) 18.5 (.73) (.285 .015) 9.1 Surface Card Guide (.36) Surface 9.1 1.5 (.06) max. (.36) 1.5 (.06) max. 6.35 6.1 (.24) min. (.250) 6.1 (.24) min. Detail of Actuating Surfaces 6.35 2.77 Required on Top and Bottom Guide Plates Detail of Actuating Surfaces (.250) (.109) Required on Top and Bottom Guide Plates Dia. FIG. B FIG. C www.calmark.com 800-854-7086 67