10.0MM WIDE SPOT ARRAY Status Designed Part no. 10624 Drawing no. 60574 Product type Optic Type Array Pieces 1 Diameter 10.0 Height 6.00 Beam Wide Spot Flange Yes Files Customer drawing (PDF) LEDs & Performances Eff. FWHM Cd/lm Spot Cross-section Files Lumileds Rebel Luxeon White 80.1% 42.8 1.5 10624 Rebel warm white 250408.ies Cree XP-E Quad XLamp Warm White 81.3% 35.9 2.2 10624 cree xpe warm white 250408.ies SSC Z5 Z - Power Cool White 77.3% 40.3 1.7 10624 Seoul Z5 pure white 250408.ies Carclo Optics endeavours to continuously improve and renew its products for this reason the technical data and contents of this catalogue may undergo variations without prior notice. For correct and up to date information, Carclo suggest using the Opticselect tool on our website Efficiency = Datasheet Value +infinity / -10% The yellowing / browning of polycarbonate lenses and holders can occur due to the natural ageing process and exposure to heat and UV and as such is not covered by Carclo&rsquo s warranty. General Instruction - Taped Holders Click here to view the 3M Technical Data Sheet When assembling the pre-taped holder onto the mating surface, the application must be made straight and square, so that the tape bonds consistently with mating surface. Assembly at an angle might cause an imperfect bond to the mating surface. Remember to ascertain the compatibility of the different substrates with the tape, as humidity and temperature fluctuations will weaken it s adhesive. To obtain optimum adhesion, the bonding surfaces must be clean, dry, free from grease and dirt and must be well unified. Some typical surface cleaning solvents are isopropyl alcohol or heptane. * * If cleaning of PCB or LED surfaces is required, please follow strictly the cleaning instructions recommended by your PCB and/or LED manufacturer - this is important to note, as cleaning in some circumstances can damage LEDs or other electronic components on the PCB. Please also note that optical components should not be cleaned using any chemicals - only a micro fibre cloth should be used to remove fingerprints or other traces from handling. * Carefully read and follow the manufacturer&rsquo s precautions and directions for use when working with solvents. These cleaning recommendations may not be compliant with the rules of certain Air Quality Management Districts in California consult applicable rules before use. Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure and moderate heat, from 100F (38C) to 130F (54C), will assist the adhesive in developing intimate contact with the bonding surface. Ideal tape application temperature range is 70F to 100F (21C to 38C). Initial tape application to surfaces at temperatures below 50F (10C) is not recommended because the adhesive becomes too firm to adhere readily. However, once properly applied, low temperature holding is generally satisfactory. During assembly the optic when placed on the PCB should be firmly held for 1-5 seconds to ensure the best possible bond. The tape will reach its final strength in 72 hours, dependent on the material and ambient conditions. We request that the customer ensures (and fully tests) the suitability and sufficiency of the bond in his product. For example, mechanical stress, vibration and holes on the surface of the circuit board can weaken the strength of the tape. Disclaimer - Taped Holders Shelf Life - There is 1 year expected shelf life from the date of purchase direct from Carclo. All Carclo lenses supplied with tape use the same high strength double-coated tape (unless otherwise mentioned in the datasheet). This tape is specifically selected for this application. These tapes generally work well together with PCBs and LEDs on the market. The customer must take the necessary measures to ensure complete compatibility with their particular application, product, PCB, LED and/or other components. Testing and verifying of the adhesives and their combinations is the responsibility of the customer. The customer is solely responsible for evaluating the application of double sided tape to Carclo Holders and the adhesion of double sided tape holders to determine whether such double-sided tape is fit for a particular purpose and suitable for the users method of application. The selection of double-sided tape in the adhesion of double sided tape holders is not covered by Carclo&rsquo s warranty. Carclo cannot take responsibility for the results obtained by others whose methods we cannot control. It is always the customer&rsquo s responsibility to determine the adhesive&rsquo s suitability for their product and to take precautions for protection of property and persons against any hazards that may be involved in the handling and use of adhesives. Carclo disclaims all warranties, including warranties of merchantability or suitability for a particular purpose, arising from use of any adhesive product. Carclo disclaims any liability for consequential or incidental damages of any kind, including lost profits. All rights reserved. No part of this publication may be copied, reproduced in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, illustrations not to be removed, without our prior permission. Carclo Optics reserves the right to make changes at any time in order to supply the best products possible. Carclo Optics 103 Buckingham Ave, Slough, Berkshire, SL1 4PF ENGLAND Tel: +44 (0)1753 575011 Fax: +44 (0)1753 811359 Page 2