Carpark Du line Configuration and Test Unit Fieldbus Installationbus Type GP 7380 0080 Portable Configuration and Test Unit Configures the Carpark sensors GP622022xx Configures the Carpark monitor GP34829091 Monitors the status of Dupline addresses LCD-display 12-key tactile keyboard Supplied by standard 9V battery Multi calibration of the Carpark sensors Possibility of simulating sensors Product Description Ordering Key GP 7380 0080 709 Configuration and Test/ Sim- simulate the precense of Type: Dupline ulations Unit for Carpark. sensors. Type no. The configurator configures Highly recommended for Supply the Carpark Sensors Carpark configuration, trou- GP622022xx and monitor bleshoothing and mainte- units GP34829091. nance Monitors the Dupline bus in GTU mode and are able to Type Selection Supply Specifications Power supply 9V battery (not included) Supply Ordering no. Type 6LR61 Internal battery GP 7380 0080 Battery Life Time (Sleep) Typ. 2 years Product Specifications General Specifications Display 2 x 16 characters Environment Type LCD Degree of protection IP 40 Height of dots 5 mm Pollution degree 3 (IEC 60664) Operating temperature 0 to +50C (+32 to +122F) Keyboard Tactile keys Storage temperature -20 to +60C (-4 to +140F) No. of keys 12 Channel keys 1-8 Humidity (non-condensing) 20 to 80% Command keys (scroll up/down) Mechanical resistance NO , YES , READ/ON Shock 15 G (11 ms) Note: Command key 0/9 Vibration 2 G (6 to 55 Hz) performs the function as Dimensions (l x w x d) 145 x 90 x 28 mm mode/Enter in GTU mode. Material ABS, grey Cable 1 GP73800080 to sensor or Weight 250 g excluding battery monitor GP73800080 connector 1 6/6 modular plug Monitor or sensor 1 6/6 modular plug Programmer cable GAP-CAB Cable 2 GP73800080 to Dupline GP73800080 connector 3 mm jack socket Dupline Bus GRIP Test cable GTU8-GRIB-CAB Specifications are subject to change without notice (27.03.2009) 1 Dupline is a registered trademark. A product of the CARLO GAVAZZI GroupGP73800080 Du line Fieldbus Installationbus Mode of Operation There are two modes of operation for Warning: Low Battery the Carpark Configuration unit: Do not plug in the Jack connector If, when activating the Configuration 1. Configuration mode and and GTU Unit, * LOW BATTERY * is when it is connected to Dupline and 2. GTU mode. showed in the display, it is time for the configuration unit is ON. This will In Configuration mode the unit can cause a short-circuit of the two wires. changing the battery. The unit will con- either program the Dupline Carpark Note: tinue to work, but it is recommended Monitor GP3482 9091 724 module or If the Dupline carrier is missing, the that the battery is changed. The bat- tery is changed by dismounting the 4 the Dupline Carpark Sensor GP6220 display will come up with the text screws on the back of the unit and 22xx 724 modules. shown in Fig. 1 removing the back cover. After that, In GTU mode the unit can monitor the After a few sec. the display will turn take out the PCB, change the 9V bat- Carpark units on the Dupline bus. off, if nothing has been done or any buttons has been pressed tery and then reassemble the unit. Pressing the Read/ On button, pow- ers the unit on in either Configuration mode or the GTU mode. Config unit (Both Sensors, Master and The modes are entered automatically Slave units) according to the connection used. If the RJ connection is used, the Config- uration mode will be entered. If the jack connector is used, the GTU mode will be entered. When the Configurator is in GTU Fig. 1 mode, the tactile key 0 / 9 has the function as Mode/Enter. Additional Information Scope of supply: 1 x Conf./Test unit GP7380 0080 1 x Programmer cable GAP CAB 1 x Test cable GTU8 GRIP CAB 2 Specifications are subject to change without notice (27.03.2009) Dupline is a registered trademark. A product of the CARLO GAVAZZI Group