Photoelectrics Retro-reflective, Polarized Type PA18C.P..., DC Miniature sensor range Range: 5 m (axial), 4 m (radial) Sensitivity adjustment by potentiometer Modulated, red light 625 nm Supply voltage: 10 to 30 VDC Output: 100 mA, NPN or PNP, N.O & N.C. Degree of protection: IP67, IP69K LED indication for output, stability and power ON Protection: reverse polarity, short circuit and transients Cable and plug versions Excellent EMC performance Product Description Ordering Key PA18CAP50PAM1SA The PA18C.P is part of a fam- Compact housing and high Type ily of inexpensive general pur- power LED for excellent Housing style pose retro-reflective sensors performance-size ratio. Housing size in industrial standard 18 mm The potentiometer used for Housing material cylindrical ABS housing. adjustment of the sensitivi- Housing type axial The sensors are useful in ty makes the sensors highly Detection principle applications where high-ac- flexible. The output type is Sensing distance curacy detection as well as NPN or PNP and the output Output type small size is required. switching function is NO and Output configuration NC. Connection type Sensitive adjustment Type Selection Housing style Range Connection Ordering no. Ordering no. S NPN PNP n Make & break switching Make & break switching M18 Axial type 5.0 m Cable PA 18 CAP 50 NASA PA 18 CAP 50 PASA M18 Axial type 5.0 m Plug PA 18 CAP 50 NAM1SA PA 18 CAP 50 PAM1SA M18 Radial type 4.0 m Cable PA 18 CRP 40 NASA PA 18 CRP 40 PASA M18 Radial type 4.0 m Plug PA 18 CRP 40 NAM1SA PA 18 CRP 40 PAM1SA Specifications according to EN60947-5-2 Rated operating distance (S) No load supply current (I ) 25 mA 24 VDC n o Axial type (A) Up to 5.0 m, Minimum operational current (I ) 0.5 mA m Radial type (R) Up to 4.0 m OFF-state current (I ) 100 A r Reference target: ER4 Voltage drop (U ) 2.0 VDC 100 mA d reflector 80 mm Protection Short-circuit, reverse Blind zone 50 mm S max. n polarity and transients Sensitivity control Adjustable by potentiometer Light source InGaAIP, LED, 625 nm Electrical adjustment 210 Mecanical adjustment 240 Light type Red, modulated Adjustable distance to target Sensing angle 2 Axial types 50-500 cm Ambient light 30.000 lux Radial types 50-400 cm Incandescent lamp Temperature drift 0.2%/C Light spot Diameter 150 mm 2.5 m Hysteresis (H) Operating frequency 500 Hz (differential travel) 20% Response time Rated operational volt. (U ) 10 to 30 VDC B OFF-ON (t ) 1.0 ms ON (ripple included) ON-OFF (t ) 1.0 ms OFF Ripple (U ) 10% rpp Power ON delay (t ) 100 ms v Output current Output function Continuous (I ) 100 mA e Type NPN or PNP Short-time (I) 100 mA Switching function NO and NC (max. load capacity 100 nF) Specifications are subject to change without notice (14.06.2017) 1 PA18C.P... Specifications (cont.) Housing material Indication Body ABS, grey Output ON LED, yellow Front material PMMA, red Signal stability and power ON LED, green Cable gland POM, Black Environment Trimmer shaft POM, Dark Grey Installation category III (IEC 60664/60664A Locknuts PBTB, black 60947-1) Mounting bracket PPA, black Pollution degree 3 (IEC 60664/60664A Connection 60947-1) Cable PVC, grey, 2 m Degree of protection IP 67, IP 69K* 2 4 x 0.25 mm , = 4.5 mm Ambient temperature Plug M12, 4-pin Operating -25 to +60C (-13 to +140F) (CONB14NF-series) Storage -40 to +70C (-40 to +158F) Weight With cable: 85 g Vibration 10 to 150 Hz, 1 mm/15 G With plug: 25 g (IEC 60068-2-6) CE-marking Yes Shock 30 g / 11ms, 3 pos, 3 neg per axis Approvals cULus (UL508) (IEC 60068-2-6, 60068-2-32) supply class 2 Rated insulation voltage 500 VAC (rms) IEC protection class III 90 * The IP69K test according to DIN 40050-9 for high-pressure, high-temperature wash-down applications. The sensor must not only be dust tight (IP6X), but also able to withstand high-pressure and steam clea- 60 ning. The sensor is exposed to high pressure water from a spray nozzle that is fed with 80C water at 8000 10000 KPa (80100bar) and a flow rate of 146L/min. The nozzle is held 100 150 mm from the sensor at angles of 0, 30, 60 and 90 for 30s each. The test device sits on a turntable that rotates with 30 a speed of 5 times per minute. The sensor must not suffer any damaging effects from the high pressure water in appearance and function. 0 Operation Diagram Operation Diagram tv = Power ON delay ON Power supply OFF Present Target Not Present Present Object Not Present Tv ON Break Output (N.C.) OFF Tv ON Make Output (N.O.) OFF Wiring Diagrams NPN PNP V V 1 BN 1 BN 4 BK 2 WH 2 WH 4 BK 3 BU 3 BU V GND V GND 2 Specifications are subject to change without notice (14.06.2017)