Photoelectrics, Fibre Optic Sensor Plastic Fibres Type PD 60 CNX 20 BP .. Range: Fibre dependent - Diffuse Reflective typ. 80 mm - Through Beam typ. 200 mm Manual distance set-up by keyboard +/- Sensitivity bar graph LEDs Microprocessor controlled and EEPROM parameter storage Operational voltage 10 - 30 V DC Output 100 mA, NPN and PNP Light or dark switching selectable IP65 protection Product Description Ordering Key PD 60 CNX 20 BP M5 The PD60CNX20BP.. is a fibre wrong polarity. The sensor is Type optic amplifier made specific build in a strong 13 x 30 x 60 Housing style for plastic fibres. The sensor is mm polycarbonate housing Housing size microprocessor based and for DIN-rail mounting. Housing material has a manual distance set-up The sensors are suitable for Not used by keyboard. NO or NC (light applications that require little Plastic fibres or dark mode) output are space and high accuracy Sensing distance cm selectable by wiring. The sen- such as: Small part detection, Output type sor output is build as a Push- tight locations, checking parts, Output configuration pull output that performs both counting, precise part posi- Connection type a NPN and PNP output which tioning, material handling and are fully protected against assembly and robotics short-circuit, transients and Type Selection Housing Range Ordering no. Ordering no. W x H x D S (Fibre dependent) NPN and PNP cable NPN and PNP plug n Make or break switching Make or break switching 13 x 30 x 60 mm 80 mm diffuse mode PD 60 CNX 20 BP PD 60 CNX 20 BP M5 200 mm through beam mode Specifications Rated operating distance (S ) See optical fibre table Voltage drop (U ) n d Diffuse mode Up to 80 mm I = 100 mA 2 VDC L Through beam mode Up to 200 mm I = 10 mA 1 VDC L Sensitivity Remote input Manual distance setup Sensitivity increase or ON 1.4 VDC decrease by pressing + or OFF 3.0 VDC - keyboard Protection Short-circuit, reverse pola- Temperature drift < 0,4%/C rity, transients Hysteresis (H) Light source GaAIAs, LED 660 nm Differential travel 5% Light type Red modulated Rated operational volt. (U ) 10 to 30 VDC B Ambient light (ripple included) Incandescent light 10000 Lux Ripple (U ) 10% Sunlight 20000 Lux rpp Output current Operating frequency 1 KHz Continuous (I ) 100 mA e Response time Short-time (I) 100 mA OFF-ON (t ) 500 s ON No load supply current (I ) 40 mA ON-OFF (t ) 500 s o OFF Power ON delay (t) 300 ms v Specifications are subject to change without notice (14.11.2011) 1PD60CNX20 BP.. Specifications (cont.) Output function Vibration 10 to 150 Hz, 0.5 mm/7.5 g NPN and PNP Available (Push-Pull output) (IEC60068-2-6) Make or break Programming by wiring Shock 2 x 1 m & 100 x 0.5 m (IEC 60068-2-6, 60068-2-32) Indication function Rated insulation voltage 50 VAC (rms) Output Green LED Sensitivity Bar graph, red Housing material Body Polycarbonate Environment Installation category II (IEC 60664/60664A 60947-1) Connection Pollution degree 3 (IEC 60664/60664A 60947-1) 2 Cable PVC, grey, 2 m, 4 x 0,25 mm Degree of protection IP 65 (IEC 60529 60947-1) Plug NPB, M8 x 1 Temperature Cables for plug (M5) CONG5A-series Operating 0 to +60C (32 to +140F) Weight 24 g Storage -20 to +80C (-4 to +176F) Approvals cUL CE-marking Yes Operation Diagram tv = Power ON delay Power supply Target present t V Break (NC) Output ON t V Make (NO) Output ON Dimensions 20 25.4 4.1 20 25.4 4.1 4.1 3 1 60 60 200 4 2 2 Specifications are subject to change without notice (14.11.2011) 13 30 + M8x1 13 30 +