Photoelectrics Through-beam, Transistor Output Type PD70CNT12.. Doors and Entrance control Range 12 m Modulated, infrared light Supply voltage: 10 to 30 VDC Output: 100 mA, NPN or PNP type Make or break switching LED for output indication or power supply Protection: reverse polarity, short circuit, transients Cable versions or M8 connector Emitter mute CE and UL325 approved Product Description Ordering Key PD70CNT12NOM5MH Type The PD70 sensor family of minium frame of e.g. sliding Housing style Photoelectric sensors is doors. Housing size specially designed for Doors The emitter has a test input Housing material and Entrance control to to turn it off for evaluation of Sensor code meet the requirements in the the sensor function. Detection principle door market. The slim hous- Available in 10-30 VDC Sensing distance ing design fits inside the alu- version. Output type Output configuration Connection type Mute input Type Selection Test Range Con- Ordering no. Ordering no. Ordering no. Ordering no. Ordering no. S nec- Receiver Receiver Receiver Receiver Emitter n tor NPN, NO NPN, NC PNP, NO PNP, NC Mute Low 12 m NO PD70CNT12NO PD70CNT12NC PD70CNT12PO PD70CNT12PC PD70CNT12ML Mute Low 12 m YES PD70CNT12NOM5 PD70CNT12NCM5 PD70CNT12POM5 PD70CNT12PCM5 PD70CNT12M5ML Mute High 12 m NO PD70CNT12MH Mute High 12 m YES PD70CNT12M5MH Note: Please order emitter and receiver separately Specifications Emitter Rated operational volt. (U ) 10 to 30 VDC Light source LED, 850 nm B Ripple (U ) 10% rrp Light type Infrared, modulated Supply current 20 mA Optical angle < 5 Protection Reverse polarity, transients Indication function Power supply ON LED, green Test input Test High Emitter off 5 to 30 VDC Emitter on < 2.5 VDC or not connected Test Low Emitter off < 2.5 VDC Emitter on 5 to 30 VDC or not connected Specifications are subject to change without notice (07.06.2010) 1PD70 Specifications Receiver Rated operating dist. (S ) 12 m Optical angle 5 n Blind zone None OFF-state current (I ) 100 A r Temperature drift 0.2%/C Voltage drop (U ) 1.8 VDC 100 mA d Hysteresis (H) 10 - 15% Protection Short-circuit, reverse pola- rity, transients Rated operational volt. (U ) 10 to 30 VDC (ripple included) B Operating frequency (f) 100 Hz Ripple (U ) 10% rrp Response time OFF-ON (t ) < 5 ms ON Output current ON-OFF (t ) < 5 ms OFF Continuous (I ) 100 mA e Short-time (I) 100 mA, Power ON delay (t ) 200 ms v (max. load capacity 100 nF) Output function No load supply current (Io) 16 mA NPN or PNP Make or break (NO or NC) Minimum operational current (I ) 0.5 mA Indication function m Output ON LED, yellow Ambient light 100.000 LUX General Specifications Environment Housing material Overvoltage category II (IEC 60664/60664A, Housing PC black 60947-1) Backpart receiver PC Green Pollution degree 3 (IEC 60664/60664A, Backpart emitter PC Red 60947-1) Connection Degree of protection IP 67 (IEC 60529, 60947-1) Cable PVC, TX: grey / RX: black, 2 Temperature 5 m, 3 x 0.14 mm , 2.9 mm Operating -25 to +55C (-13 to +131F) Plug M8 - 3 pole Storage -40 to +70C (-40 to +158F) Weight (each sensor) Vibration 10 to 150 Hz, 0.5 mm/7.5 g With cable 90 g (IEC 60068-2-6) With plug 20 g Shock 2 x 1 m & 100 x 0.5 m CE-marking EN12445, EN12453, (IEC 60068-2-32) EN12978 Rated insulation voltage 50 VDC UL-Approval c us UL325, CSA-C22.2 No.247 Operation Diagram tv = Power ON delay Power supply Target emitter present Object present Break (NC) Output ON Make (NO) Output ON Test active High (MH) Test active Low (ML) Installation Hints To avoid interference from inductive voltage/ Relief of cable strain Protection of the sensing face Switch mounted on mobile carrier current peaks, separate the prox. switch pow- er cables from any other power cables, e.g. motor, contactor or solenoid cables Incorrect Correct The cable should not be pulled A proximity switch should not serve as Any repetitive flexing of the mechanical stop cable should be avoided 2 Specifications are subject to change without notice (07.06.2010)