Photoelectrics Retro-reflective, Polarized, Relay Output Type PMP Range: 6 m Modulated, visible light, polarized Make or break switching function (switch selectable) LED-indication for target detected Multi supply voltage: 12 to 240 VDC and 24 to 240 VAC, 50/60 Hz 25 x 65 x 81 mm reinforced PC/ABS- housing, IP 67 Timer options (adjustable) NO and NC output Product Descrip tion Ordering Key PMP 6 R G T Retro-reflective photo e lec tric tion. 25 x 65 x 81 mm pla stic Type switch with polarized light. hous ing. PG 13.5 or 1/2 NPT Range Range up to 6 m. Fixed sensi - cable gland. Timer options: Output tiv it y. Im mune to ambi ent light. Delay on operate, delay on Cable gland type Output func tion switch selec- release, one shot (trig gered Timer function table. Pro tec tion de gree IP on leading or trail ing edge). 67. Screw ter mi nal con nec- Type Selection Housing Range Ordering no. W x H x D (S ) with timer n 25 x 65 x 81 PG 13.5 cable gland 6 m PMP 6R GT 1/2 NPT cable gland 6 m PMP 6R IT Specifications Rated operating dist. (S ) PMP6.. 6 m Operating frequency 20 Hz n (0 to 5,000 lux) with reflector type ER 4, Response time ref. target OFF-ON (t) 20 ms ON Blind zone 0.15 m ON-OFF (t) 30 ms OFF Rated operational volt. (U ) 10.8 to 264 VDC Power ON delay (t) 300 ms (typ. 100 ms) B v AC: 45 to 65 Hz 21.6 to 264 VAC Output function Switch selectable, make or break switching Rated operational power (relay ON) 2 W (2.5 VA) Indication Target detected LED, yellow Output Contact ratings (AgCdO) (micro gap) Optional timer Resistive loads AC 1 3 A/250 VAC Delay on operate 0.1 to 7 s 2 s DC 1 3 A/30 VDC Delay on release 0.1 to 7 s 2 s Small inductive loads AC 15 2 A/250 VAC One shot 0.1 to 7 s 2 s DC 13 3 A/30 VDC Environment 6 Mechanical life (typical) 40 x 10 operations Overvoltage category III (IEC 60664/60664A 5 Electrical life (typical) 5 x 10 operations 60947-1) at 220 VAC - 3 A resistive Pollution degree 3 (IEC 60664/60664A load: 360 impulses/h 60947-1) Dielectric voltage 2,000 VAC (rms) Degree of protection IP 67 (IEC 60529 60947-1) (cont./supply) Temperature Sensitivity Fixed Operating -25 to +55C (-13 to +131F) Stor age -30 to +80C (-22 to +176F) Light source GaAlAs, LED, 660 nm Light type Visible, modulated Optical angle 2 Light spot size 280 mm at 4 m Specifications are subject to change without notice (22.01.2015) 1 PMP Specifications (cont.) Truth Table Vibration 10 to 150 Hz, 0.5 mm/7.5 g Make switching Break switching (IEC 60068-2-6) Shock 2 x 1 m & 100 x 0.5 m Object present Yes No Yes No (IEC 60068-2-32) LED OFF ON OFF ON Rated insulation voltage 250 VAC (rms) Load Non- Active Active Non- Housing material active active Body PC/ABS, grey Front PMMA, red Cover PC, black Cable gland PA, black, reinforced Mounting bracket Steel, black Connection 2 Screw terminal 5 x 2 x 1 mm Cable gland PG 13.5 or 1/2 NPT for cable 6 to 10 mm Weight 110 g Approvals UL, CSA CE-marking Yes Connection Diagram Selection of Function Switch 1 2 3 Time adjustment PMP 6R . 1 Delay on operate - Break switching 2 Delay on operate - Make switching 3 Delay on release - Break switching LED 4 Delay on release - Make switching DIP switches 5 One shot, trailing edge - 12 - 240 VDC Break switching 24 - 240 VAC 6 One shot, trailing edge - 50/60 Hz Make switching 7 One shot, leading edge - 30 VDC Break switching 250 VAC 8 One shot, leading edge - Max. 3 A Make switching Upper postion ON (Mode 1) Lower position OFF (Mode 0) Installation Hints To avoid interference from inductive voltage/ Relief of cable strain Protection of the sensing face Switch mounted on mobile carrier current peaks, separate the prox. switch power cables from any other power cables, e.g. motor, contactor or solenoid cables Incorrect Correct The cable should not be pulled Any repetitive flexing of the A proximity switch should not serve as mechanical stop cable should be avoided 2 Specifications are subject to change without notice (22.01.2015)